what pipes are these ?

VXR230BHP

Member +
Rep given to all of ye if you can help !!! the two pipes on the front of the inlet mani to the left of the throttle body ? 2, the pipe thats on the first port of the mani on the right, 3,the pipe at the back on the right at the top and bottom middle, 4, the two pipes that are directly below the throttle body, 5, the pipe thats connected onto the sensor on the right on the mani at the bottom ?
 

corofin12345

Member +
1. left pipe for vacuum off bov.. right one for pcv valve on rocker cover
2. unsure what you mean?
3. top right is for aircon and bottom middle is for map sensor
4. underneath throttle boday are water pipes and vacuum pipes (dont mix up) brass pipes for vacuum
5. unsure what you mean?
 
Last edited:

VXR230BHP

Member +
1. left pipe for vacuum off bov.. right one for pcv valve on rocker cover
2. unsure what you mean?
3. top right is for aircon and bottom middle is for map sensor
4. underneath throttle boday are water pipes and vacuum pipes (dont mix up) brass pipes for vacuum
5. unsure what you mean?

Ok mate !
1)the water pipes and vacuum where do they connect to ?
2)whats the PCV valve on the rocker cover ?
3)the sensor on the inlet mani think it has somethin to do with idle control, has a short pipe coming out of the bottom, not sure where it connects to
4)at the top I've got three spouts, one small one in the middle for map sensor, the one on the right pointing directly up for aircon but the one on the left is pointing up at angle i'am not sure what connects on to this ????
5) the water pipe spouts do these two just connect together?
5)the first port on the inlet mani (drivers side ) has a small little spout sort of off centre, what connects on to this ???
 
Last edited:

corofin12345

Member +
heres a few pics.. i will look at my car 2moro to see about the water pipes cause i just cant remember

hose1.jpg

hose2.jpg


(dont mind dots over strut brace)

alan1-1.jpg


1. green dot at front of mani = vacuum for dumpvalve
2. red line is the hose from inlet mani to pcv valve on rocker cover
3. yellow line goes from small pipe on top of throttle body to sensor and from sensor to carbon canister (second picture above)
4. pink line goes from big pipe on top of throttle body to a/c sensor (first picture above)
5. light blue line goes from back top right of inlet mani to a/c sensor ( you can see it in first picture, top left)
6. green line goes from middle back of inlet mani to map sensor
7. white line goes from back left of inlet mani to barke servo

---------------------------------------------------------------------------------------------------

alan1-2.jpg


8. the pipe near first runner of inlet mani (drivers side) goes to bottom idle control valve for vacuum.. red line
 
Last edited:

VXR230BHP

Member +
You are a legend mate !!! thanks. Theres a pipe bolted directly onto the mani at the back and right in the centre is another tiny spout also ???

Also the two brass spouts that are the vac ! where do I connect these onto ????
 

corofin12345

Member +
this is goin to be tricky 2 explain so ill try my best
------------------------------------------------

aea.jpg


1. (vacuum).. this hose goes to first pipe on long pipe on back of inlet mani (the one that runs behind inlet mani closest to throttle body)
2A. "see picture down below"
3. (water).. this hose goes onto big water pipe at back of engine. (the one coming from water pump,half way along there a small pipe)
4. (water).. this hose off throttle body goes to the head (follow the return feed to head from heater matrix at bulkhead and you will see pipe)
----------------------------------------------------------------------------------------------------------------------------------------

picture below shows a breather unit on top of steering rack..(green dot) two hoses come off this..
-------------------------------------------------------------------------------------------------------

aed2-1.jpg


1. (vacuum) this hose goes to pipe that runs behind inlet mani (near middle)
2B. (vacuum) this hose goes to throttle body (number 2 in picture of throttle body)



you own me 10 beers.. that was a pain..lol
 
Last edited:

H_D

Member +
this is goin to be tricky 2 explain so ill try my best
------------------------------------------------

aea.jpg


1. (vacuum).. this hose goes to first pipe on long pipe on back of inlet mani (the one that runs behind inlet mani closest to throttle body)
2A. "see picture down below"
3. (water).. this hose goes onto big water pipe at back of engine. (the one coming from water pump,half way along there a small pipe)
4. (water).. this hose off throttle body goes to the head (follow the return feed to head from heater matrix at bulkhead and you will see pipe)
----------------------------------------------------------------------------------------------------------------------------------------

picture below shows a breather unit on top of steering rack..(green dot) two hoses come off this..
-------------------------------------------------------------------------------------------------------

aed2-1.jpg


1. (vacuum) this hose goes to pipe that runs behind inlet mani (near middle)
2B. (vacuum) this hose goes to throttle body (number 2 in picture of throttle body)



you own me 10 beers.. that was a pain..lol

Brilliant
 
  • Like
Reactions: Jay
Top