Search results

Hi i bought a td04 kit Of akaye4000 was told it was fully workin and have now found out the wheel wont move inside and is knackered ! £485 i have paid for it

After the gasket that goes between the decat/downpipe and the centre exhaust pipe its a triangular shaped one. Not the decat to turbo one. Pm me

Where can i get the triangular shaped gasket that goes in between bottom of the decat pipe and exhaust ? Not the turbo to decat one. Looked on camskill n ebay cant see any

Does anyone know the size of the blue silicone hose joiner that comes of he inlet mani to the fmic pipe in mm? Just after the size so i can get one with a dump valve bung in it for when i go td04 :)

Looking around for a td04 kit with mani n decat oil water lines/feeds etc ready to bolt on for june pm if anything going

Got some nasty high pitch sound at high revs when i giv the car a bit of welly duno what it is any ideas?

Hi just fitted a blitz bov bought of ebay came of a 95 scooby wrx as my old dump valve was too small and just made the flutter sond from the turbo which i think causes lag anyway its still making the flutter sound and not the dump valve sound now Its fitted so basicaly is it not working?

Im after the plastic cover inside the boot lid and the fittings screws/bolts if pos, that covers the electric wires as ive stripped my rear out and it looks stupid with the wires exposed as mines. Issing when i bought the car

Td04 or stay stock ct9, Thinking about doing the td04 conversion and runin it just under a bar. But cant decide to do it or not. Has anyone done it on the cheap? anyone live near birmingham with a td04 glanza on stock engine thats can take me for a spin so i can decide lol

Any one got any ideas on stripping outthe rear where to mount 6x9s as front ones on there own sound shit and making up boot lining, carpet etc to make it look tidy as i ent keen on it being bare, like a track car, Post up pics of yours if anyone has

Is it ok to jack up front end using front crossmember the bit where the bottom of the bumper and bottom of the fmic core bolts to underneath. As i just want to jack the whole front end up rather then one side at a time for when i change the oil the weekend. And wheres best place to put axle...

Anyone know of a good tuner in or near Birmingham ? Preferably in west midlands area? That can Fit and map a ecu piggyback ?

What sort of power Gains can I get from a piggyback mapped? thinking of getting an emanage blue but thought about goin td04 conversion prob one or the other as can't afford both. ATM my setup is running 0.9 bar of boost on hks actuator, fmic, front air filter kit, wepr mani, fuel pressure...

anyone kno where i can get a oil filter sandwhich plate so i can fit my oil temp gauge, one that does fit proply and doesnt rub againest anything, if there is one available to buy like this would appreciate it if u could point me in the direction of one. ive got an air filter relocation kit...

anyone help me here, ive just fitted a new boost gauge as the old one was a bit difficult to read, as it had these bars that lit up and was hard to tell where it stopped if you get me. bought one that reads in bar its much better it has the actual needle and i can read proply. But i fitted it...

just wondering what sort of things shagged engine and gearbox bushes can effect as in the drive/feel of the car etc having mine replaced with some poly ones monday so hoping for improvements :p

can anyone help me out give me some pointers and tip how to fit a manifold to the original ct9 turbo without having to take everything out i.e turbo, rad etc, ive looked for threads and cant find any that are much use as they all involve taking out shit loads of stuff which i wanted to avoid. i...

after an Exedy race clutch such as the organic one to replace my standard one, preferbaly unused/new dont want a wornout one, might go for another brand aslong as its a race clutch and can take abuse lol what you got? pm me

when i pull of in first hard i never get it on lower boost 10 psi below etc but im running 0.9 bar and when i pull of fast the cars revs will go up fast as normal but it will feel like the cars wheels spinning n engine vibratin abit and just takes the piss to actually bite and get the power...

has anyone made a heat shield for the bumper cut out for the backbox for their glanza? if you have how have you done it and what have you used ?? because the exhaust on mine that the person before me put on has made a right mess smeared the paint it and the paints cracked above it aswell, it...