Search results

Anyone selling the above or know where u can buy one please?

Hi guys. I have searched the forum for this but haven't found anything concrete. What is the maximum injector size we can run on our engines with the EMU? A friend of mine has some 740cc he is not using so i was considering buying it from him but wanted to check if it will work first. I do...

Hey guys, My car finally went in today for forging :rockon: I need some info from you. My tuner wants to know what is the inlet opening angle (degrees) and also the full lift inlet is at what crank angle (degrees). I have stock cams, but using Zisco uprated valve springs. 1.2mm...

Guys and girls, Is that website any good? I came across uprated valve springs there but i do not know them. http://www.futuremotorsports.com/Uprated-Valve-Springs-30-Stiffer-4EFTE.html Any advice? cheers, Luc

Guys, I am after these parts for my 4E-FTE: Adjustable cam pulley (Oxidised red) Uprated valve springs Clear cam cover Any idea where i can get them please? cheers

Hey guys, as above, what's the thickness of the standard cylinder head gasket?

Got my coilovers already!! Thanks Jerrick for putting up with me ;) BTW I have messed up the screws while trying to camber the front ones. Do you sell the pillowballs separately?

Hi Guys, I have just received my indiglo dials today and i've already installed them in my cluster. However, i have this cable which i do not know where it goes. See the one im holding in my hand below: I also have 5 dials but the power pack comes with only four connections, can i splice...

Hi guys and girls, As above, i was wondering if i need to have forged pistons and rods to be able to rev at 8k and over. Can i just upgrade my cams and springs to do that? And will my EMU be able to get rid of the rev cut limit? I see a check box in there which allows to do that.

I want to know if any of you guys have a decent brand new or used electronic boost controller for sale. It will need to be shipped to Seychelles, so please calculate shipping cost too. PM me.

Guys, Is there much difference if i use a 2 core or a 3 core rad? I am stuck between the speedvision 2 core one and the TD 3 core one. cheers, Perreau

Hi guys. We are having this weird problem with my GT. It just died on us while lifting in 1st gear. Had to be dragged back home. The car cranks, we see sparks in the plugs. Cams turn. timing belt is fine. Head gasket is ok. Compression seems ok. Wiring seems ok. Injectors are ok. Coil and...

Guys, Girls, My EMU was fine until recently started giving me the blinking red light with the following error codes: [2011/06/20-17:41:06]------------------------ 125:0204-0028[Flash Read Error] 126:0204-0029[Flash Read Error] 127:0204-0028[Flash Read Error] 65408:0204-0029[Flash...

Guys, Girls, anyone selling a gearbox with aftermarket LSD already installed? Its for my Manual EP82. cheers.

Hi Guys, Where is the best place to get a pair of Mickey Thomson slicks and what's the recommended size for my GT? Any specific one i should go for? I need for hot, dry use. cheers.

Guys, i have installed a Blitz SBC and i am going to attempt to control the boost using my EMU. I have already modified JP20 to 1-2 and using the sub injector map to do this. My problem is, on the sub inj map, i get only air flow, throttle position and absolute pressure. I am using the...

Guys, We checked and cross checked all wiring and found nothing abnormal. Inj map 1 has to be set at -30 for car to idle properly and gives slight misfires when set at 0. Ign map is set to 0 too. This is our jumper setting for the EMU, looks OK right? JP1-6: OPEN (to trim and add...

Hi Guys, My wife will be in London this Sunday (26/09/2010) and i would like to know the best way for her to buy me a knock meter there. She will be in the Heathrow area, she can reach the Hounslow, Staines or Slough area. Are there any shops in that area which have that in stock so...

Hi guys, what parts do i need to use EMU as an electronic boost controller? cheers, Perreau

Hi guys. My EMU is installed and i'm almost there with my launch control setup. However i have this problem. Whenever i connect the Throttle Position Sensor input cable from EMU pinout 16 to the EP82 wiring pinout 17 PSW (Throttle Position Sensor) on connector 1 (26P), i can get the throttle...