Search results

Looking for a tidy unmolested gt standard or otherwise with quality mods no ebay crap Thanks

My Starlets going in the next few weeks so these bits are surplus For sale:Suede effect dished wheel and HKB Boss Item Condition:Good used for a few months Price and price conditions:Sold Extra Info:Wheel bought from autosport unknown make will include the center etc Pictures...

For sale:SPS Mild steel Manifold Item Condition:Cracked at the back down the center as used without a braced decat, has been prepped for welding Price and price conditions:£50 Extra Info: Pictures: Contact Details:PM Location:Southend on Sea Delivery & Conditions of...

Turbos just started puffing smoke on idle does anyone have a nice low milage one they want rid off

Hello Bought Starlet number 5 last October, then packed it up for the winter and almost sold it about 10 times, but new I would regret it and be buying another a few months down the line if i did. So after gathering up a few parts I have just sorted it out and got it back on the road and am...

For sale: What you can see in the pics Item Condition: Used All the pistons have cracked ringlands The Rolla mani has a RB25 Throttle body flange Price and price conditions:5-50 Extra Info: Pictures: Contact Details:PM Location: Southend on Sea Delivery &...

Sorry if this is the wrong section Just wondering if any of the moderators or anyone else has contact with Frank as I sent him payment for a relocation kit two weeks ago but havent had any contact from him an he doesnt seem to have been on here for ten days. I understand hes admin and I'm not...

For sale: J Performance Type 2 intercooler for Starlet Turbo Item Condition: The two pipes which are unrapped have been offered upto the car for fitment and have a few small scratches, the rest of the kit is as new. Price and price conditions:£250 ono Extra Info:Short route for...

For sale:1995 Toyota Starlet GT turbo Auto Item Condition:Used drives great Price and price conditions:£1195 Extra Info: MOT 23rd May 2013 TAX End Oct 2012 95,000 miles Some history and import docs Mechanically Owned the Car since last October it has had 3 owners Since owning...

Fitted a set of Tein Mono/Master Flex Coiovers the other week and now they have settled I am looking to fine tune the ride heat slightly. I wasnt given any instructions with them but from what I have seen do I adjust the height by loosening the locking ring at the bottom of the shock then...

Keep gathering parts to try and progress with my project but its simply not happening and I lost one of my jobs so here goes. For sale:Tein Monoflex Coilovers Item Condition:Used for 1000miles according to previous owner I havent even fitted them:( Price and price conditions:£500...

Here are some parts I have from a Mark 1 GT that I bought to convert my auto if you need anything thats not listed just ask. Thanks Joe For sale: Mark 1 Light up rear panel SOLD Item Condition:Very good some very light marks that the camera wont pick up. Price and price conditions:£60 Extra...

Looking to restore the underside of my gt as there's a fare amount of surface rust and I want to keep it a solid base to improve on. I'm planning to take a wire wheel to the affected areas acid/zinc etch primer it then a coat of normal primer followed by underseal/hammerite and then stone chip...

For sale:4efte Crank and ACl Bearings to suit. Item Condition:As New Price and price conditions:£250 ono Extra Info: Removed from an engine with 70k amd piston failure was in mint condition and all journals were I fine I then had my Machinist Check and balance it. Will sell bearings...

Need to work this out for a presentation I'm doing tomorrow can anyone help

Want these gone make me an offer For sale:Wiseco 74.5mm Pistons Item Condition:New Unused Price and price conditions:New £300 Extra Info:Boxed as New Pictures: Contact Details:PM Location:Weybridge Surrey Delivery & Conditions of Delivery:Included For sale:Pauter...

No longer for sale

I'm looking to calculate how much weight I have reduced my bottom end by and forgot to weigh it all individually before I had the work carried out. Has anyone gone to the trouble of weighing it all?

I have been speaking to my engine builder and he has said that on all wiseco pistons he has fitted previously, he allowed a bit more clearance than stated by wiseco due to there expansion. Now I'm abit worried as I havent heard alot on here about anything like this and I wouldnt want the engine...

As above preferably a Paddle. Thanks Joe