Search results

  1. danturbo4311

    Last bits left from my ep82

    For sale: 38mm genuine tial external wastegate Item Condition: Used but works fine Price and price conditions: £100 delivered Extra Info: This came off of my ep82 and held 1.8bar of boost fine and comes with gaskets bolts etc (used condition) Pictures: Contact Details: pm me Location...
  2. danturbo4311

    Life after the starlet.... motorbike time

    After breaking my ep82 I have been on the hunt for a nice motorbike and after viewing a few I have now put a deposit down on one this morning. Its a Suzuki gsxr 600 K5 20th anniversary edition (basically comes with a different exhaust and more carbon bits and slightly different paint job than...
  3. danturbo4311

    Meister Rs, anti roll bar, paddle clutch, strut braces.

    Tial wastegate, Intercooler, EHPAS pump to fit starlet For sale: TRD Engine mount set Item Condition: the mounts are in good condition, however the drivers side mount needs a tap run through it to clean up the thread were the stud goes through as its slightly damaged, but will be fine once...
  4. danturbo4311

    Auto starlet/car wanted

    Hi guys and girls I am after an automatic starlet or really any automatic car (can be semi auto to) ideally looking for a cheap run around as a learner car (for the misses). I have a 324whp EP82 that I am currently breaking (includes a forged 4e engine built at sumo and many more parts, pm me...
  5. danturbo4311

    Breaking a few parts from my EP82 Race tech inlet, bootlid, gearbox and other bits

    For sale: Gt gearbox Item Condition: Used & crunches. Bit dirty/rusty as its been sitting in the shed for a few months Price and price conditions: £60 ono Extra Info: It crunches into second most of the time and third occasionally, so really needs new synchros. Ideal for some who has the time...
  6. danturbo4311

    TPS idle screw

    Hi everyone, I got a problem with my ep82 its mis firing when accelerating, today I've been fiddling with the tps. I am running a race tech inlet mani with a race tech throttle body with a standard EP82 throttle position switch and EMU. When setting the resistances on the TPS do you need to wind...
  7. danturbo4311

    New Front Stub Axle

    Anyone know where I can get a new front stub axle from for an EP82 1995. As Iv just stripped down the front hub and pressed out the wheel bearing then found that its badly worn the stub axle away.
  8. danturbo4311

    Front passengers side hub

    Im in need of a front passengers side hub, to fit an ep82 without ABS please.
  9. danturbo4311

    camshaft seal keeps leaking

    Iv been running speedvision cams for about 8000 miles been keeping a close eye on them due to the problems others have had with head, valve & cam damage etc. As im also running his uprated valve springs too but with custom retainers, to set the correct spring base pressure. So far it has all...
  10. danturbo4311

    Front wiper arms .

    Anyone have any front wiper arms for sale to fit an ep82, also anyone know if glanza or n/a wiper arms fit the ep82?
  11. danturbo4311

    Broke down on christmas day

    Iv just received a christmas present from my car, it broke down on my way home from seeing family & it seems to be a bit of an odd problem. As soon as I left to go home I started the car up & it sounded slightly strange, but it started up & I drove off, then about 20minutes into the journey...
  12. danturbo4311

    Fuel in oil

    Hello everyone, Im having a problem with fuel getting into the oil on my freshly rebuilt forged 4e which has done just over 400 miles (still running it in) has anyone else had a problem like this when running there engine in as im not sure if its because the rings have not bed in properly yet or...
  13. danturbo4311

    Starter motor needed

    Im in need of a starter motor & solenoid please, in good working condition thanks
  14. danturbo4311

    Nitrous kit for sale

    For sale: Wizard of nos kit single point injection Item Condition: Used, bottle almost full, everything works. Price and price conditions: £500 cash Extra Info: SB150i Nitrous Kit (wet kit) with an 11lb bottle, almost full, only been used twice, comes complete with minimax...
  15. danturbo4311

    Needed ASAP please

    Im in need of both .25 big end & .25 main bearings asap, or a good condition crankshaft which doesnt need a grind anyone help in the south of england will come to collect & pay by cash. thanks Dan
  16. danturbo4311

    Oil pump ASAP

    Im in need of an oil pump O ring type to fit a 4EFTE, will pick up in or around the london area as I need it by monday if possible. thanks Dan
  17. danturbo4311

    Offset dowel pins

    Any of the traders on here sell, or no were I can get hold of some offset dowel pins to fit starlet cams. Also in what offset do they come in & how much do they cost?
  18. danturbo4311

    What Arp bolts come with scat con rods

    I need to get a new set of ARP 2000 bolts to fit the scat rods, Iv been in contact with scat & they have said there are 2 types of bolts they use for starlets, one with a thread of 3/8" x1.6 part number #4AJ1.601-25LU or the 5/16" bolts part number #3AG15052U. Its been a while since I fitted...
  19. danturbo4311

    Emanage Blue for sale

    For sale: E-manage Blue Item Condition: Used, but good working condition Price and price conditions: £155 delivered including pay pal fees. Extra Info: Was mapped for an EP82 with a t25 @ 1.2 bar & made 268bhp, on 460cc injectors, Can be re-mapped for any set up & fits both ep82 & ep91...
  20. danturbo4311

    External wastegate

    Anyone got an external wastegate for sale preferably tial or turbosmart thanks Dan
Top