Search results

So I figured it was time to make one of these. Im gonna start with my "paseo story". Its gonna be long so scroll down to the good stuff if you dont care to read. So my Paseo life started when I was working at VW at a car porter before I moved to sales. I needed a car as my other car spun a...

this is by far one of the worst search features Ive used on a forum. Ive been in the forum game for a while. Same questions keep popping up over and over. The search only allows for 4 or more characters. Second, the whole 15sec timer between searches make searching that much more a pain. It...

For sale: Toyota 5efhe rods and pistons used. New Toyota rings, rod bolts, and nuts. Item Condition:Very good Price and price conditions: $200 or trade Extra Info: One piston is damaged when I bought it. So I sourced a single 5EFHE piston. I would just suggest taking it to a machine...

Whose got one? PM me.

I need the part number for the 4efte entire gasket, distributor cap, distributor rotor. I have an EP82 4e if that makes a difference. Does the 4e gasket set from Toyota come with any turbo gaskets? I assume it has to have something different than the 5efe gasket set or is it the same part...

what do you guys think about them

heres a list put together with the research i did on www.miataturbo.wikidot.com, www.witchhunter.com, www.rx7club.com, www.honda-tech.com, www.tercelreference.com, and the best for last www.TERCELONLINE.com :drive:. High Impedance - No resistor box required:rockon: Toyota MR2 4AGE 213cc –...

heres a list put together with the research i did on www.miataturbo.wikidot.com, www.witchhunter.com, www.rx7club.com, www.honda-tech.com, www.tercelreference.com, and the best for last www.TERCELONLINE.com :drive:. High Impedance - No resistor box required:rockon: Toyota MR2 4AGE 213cc –...

if you are rebuilding a motor what do u do first? do your break-in period or take it to be dyno tuned, then broken in. im know its a matter of mostly opinion/preference. but i want to see where this debate goes.

i am planning on using 4e electronics and such. but i had an idea. since i have an emanage blue on the way can i just stick with all my 5e stuff and slap in the 4e turbo stuff and control it with the emb. (im talking electronics here as im using everything from the 4e except for the 5e block...

need a set of these shipped to the states.

not for my car but a buddy is replacing his bent rod. his compression is fine across the board he says. since hes only replacing the rod and not the piston. is it ok to pull the piston/rod out, replace the bent rod with 4 fresh rods and just use the same piston with rings since we dont want...

so after a long debate with myself and friends ive decided im going to build 2 engines. the reason being is i dont want my car out of commission for 6 months. im paying off some old debt which limits the amount i can spend on my car. the forged build i want to do is close to 4grand. the build im...

Items I am in the market for. acl race main/rod bearings lightweight flywheel uprated clutch (good company and at least 250hp rated) 5e complete gasket and seal kit 5e uprated metal hg 4e ct9 uprated mani arp headbolts 4e distributor cap and rotor brush wideband lightweight crank...

this is the tranny from my 93 paseo. it was swapped by the person i bought it from so idk where the engine originates from. its and ep82. heres the block fi it helps the bar that leads me to believe its lsd this is weird. the one on the left was the passenger side and the one...

have these up for sale on TO.com but thought i post them up here if some1 from here might need one of these items. shipping is from the USA. I am up for trades, let me know what you have. For sale: 4efte clutch and pressure plate Item Condition: used Price and price conditions...

do toyota oe rings come pre gapped? i dont want the hassle of gapping myself and i dont want to risk messing up something so minute and my motor blows up in 15 minutes. the setup im building is a 5e with 4e electronics and turbo. so i assume i would be using the 4e rings?

car smokes bad on idle. has been getting worse. oil steam comes from dipstick. breather filter on rocker cover is drenched in oil. what do u think it is? rep will be given

i been reading threads about aftermarket manis and stock manis and porting stock manis. its funny how the the sellers of aftermarket parts will always tell you that the stock mani is crap and they even think that even if your 4e is stock it should still have an uprated mani. i think toyota R&D...

i have the epc up to from 69-95. the only problem is it doesnt have a ep82 or 91. it only goes to ep81 for some reason. can some1 help me out? heres the screen shot