anyone runnig a HKS super-AFR?

Discussion in 'ELECTRICAL' started by thomllee1981, Aug 21, 2008.

  1. thomllee1981

    thomllee1981 Paid Member

    after some help people
    have a HKS super-AFR but doesnt seem to be working not sure why was turned on but stopped the car revving!

    anyone got 1 fitted would love to know how yours is wired in and setup.

    cheers
     
  2. sx_turbo

    sx_turbo Paid Member

    sounds like he wired it in wrong
     
  3. thomllee1981

    thomllee1981 Paid Member

    not sure that would happen with a manual for the super-afr and ecu pin out

    might have been to with jam fcc being in as well not sure what order things should be in.
     
  4. Chris@CCM

    Chris@CCM Registered User +

    tbh buddy there no use at all i would just take it out
     
  5. thomllee1981

    thomllee1981 Paid Member

    so you rip out an apexi one as well then yeah?
     
  6. sx_turbo

    sx_turbo Paid Member

    i think chris thinks you have the one that looks like an fcd
     
  7. sx_turbo

    sx_turbo Paid Member

    he is also semi right, safc are only good for trimming down fuel.

    a safc etc wont fuel over fuel cut.

    but should be just fine for your needs :)
     
  8. thomllee1981

    thomllee1981 Paid Member

  9. seed

    seed Paid Member

    Was using this on mine and it worked great. Same as an SAFC but not as posh minus the screen but it does the job.
     
  10. thomllee1981

    thomllee1981 Paid Member

    who set it up for you seed? (you should know as you sold it to me!:p)
    i may just take it to them and get them to sort it out, i know the bloke putting it in has done them before just not on a starlet!
     
  11. sx_turbo

    sx_turbo Paid Member

    there should only be 4 wires on it.

    i think the guy got the wrong pin out when wiring it in.
     
  12. thomllee1981

    thomllee1981 Paid Member

    yeah would have been nice to get my printouts but the printer got broke doing the run before mine!!!!!
    so not sure the exacts on the fueling but you can raise on this unit so it should do what i need it to.
     
  13. thomllee1981

    thomllee1981 Paid Member

    nope ricky theres 6!

    pressure to ecu
    pressure away from ecu
    12v ignition
    ground
    RPM signal
    throttle position sensor signal
     
    Last edited: Aug 22, 2008
  14. sx_turbo

    sx_turbo Paid Member

    yeah thats what i meant.


    starlets dont really use the throttle position sensor.

    on a starlet it's on or off.


    also he needs to make sure the dip switches were in the correct places.


    it doesnt help that there is no wiring diagram specific for the starlet on the hks website
     
    1 person likes this.
  15. sx_turbo

    sx_turbo Paid Member

    yes you can raise it but not above fuel cut :)
     
  16. seed

    seed Paid Member

    Hehe. Didn't bring it to any tuner. Mapped it on the run with the wideband. A friend did it for me, so it's not that spot on accurate but does the job
     
  17. thomllee1981

    thomllee1981 Paid Member

    no it doesnt help did give the guy ecu pinouts and the hks instructions so he should have been able to get it working
     
  18. seed

    seed Paid Member

    Correct! You don't have to wire in the throttle position sensor.
     
  19. thomllee1981

    thomllee1981 Paid Member

    i have no fuel cut! (jam FCC fitted)
     
  20. thomllee1981

    thomllee1981 Paid Member

    can someone tell me which wires go where on a pre92 ecu then?

    as cant work out which 1 is for rpm signal
    and pressure (airflow)
     
    Last edited: Aug 22, 2008

Share This Page