Search results

Hey all, Got a jam fcd and want some answers from you fine people on wiring. Basically it was wired in but previous owner cut the wires but after a big of head scratching and some great help from another gt mate I've just met it turns out it has a live and it's earthed BUT the other wires...

Hey, wondered about where you can buy flares, preferably original ( long shot I know as people usually snap em for fun ) Just would like to collect these rare items.. On the subject of rare optionals what are they?

Beeped at me when you drove past :)

I was going to replace my pcv but then though hang on il take it out and put a catch can in.. When you remove the pcv and grommet is it threaded cause a lot of catch cans come with the unions which the hoses goes onto.. Will it be ok and fit a pipe on there with the top mount on??

Hey guys, when relocating my filter I stumbled across a sensor that plugs into a hole on the standard intake piping.. What is this? Air temp sensor?? Just what do you do with it once you relocate? :confused:

Hey guys looking to do camber change this month but have no air compressor to connect my air gun and was wondering is there anyway (other than leavering on the flywheel, which is easy if the engine is out, but it's not lol.. ) to lock the engine and stop it from turning whilst I leaver on the...

Right guys I replaced my stat other week and it leaked fisrt time but I'd crushed the seal on tightening.. So re did it and it's fine but today I changed the coolant sensor and got to work and saw some drops of coolant dropping on the gearbox... All I did was change the sensor but obv when take...

Chekc out this glanza i found making this insain racket!! http://www.youtube.com/watch?v=zRQA_7Fvi9Q

How do you find or does anyone know of a website or anything which can help you find out about past owners or import infomation? Just im curious about my cars history :)

Hey guys, Ive had my glanza for over a year now and i do know there are common cases of oil leaks but mine has a bit of mistyness around the crank pully i suspect the usual glanza faults.. but its never shown on the dipstick even after a year of driving it everyday.. I will clean and inspect...

As above It stopped working a while ago.. I put new bulb in today but it ain't working checked dome fuse- ok and fuses under steering wheel :/ my fuel light also stopped working around same time.. Are they related in the electrical system?

Hey All! Just wj seeing who jn here let's their pets in their cars lol :)

Hey I'm ordering a icv cause I was at witts end with it now. I've had lots of good advice off all you guys on here but I final clarification before I go out and spend £95 quid on a new one. Nh car idles at 2000rpm and jumps like MAD and will not stop its just up and down in park constantly.. And...

Hey... Again lol! In the fuse box under dash there's a fuse that controls ecu-ig mind didn't have a fuse in it :/ I put one in now though. Cheers guys appreciated as always:)

Hey all, I got a jam fcd on my glsnza and after a few mods I've just started to hit fuel cut :( the previous owner cut the wires as he said if was running shit when he got it so he cut the wires.. Obviously hadn't got it tuned. Well to the point lol.. He's cut the wires right down to the box...

As above :)

Hey all just recently changed my stat and bled system with heaters on and no rad cap, however the hoses are flat when the engine is switched off? I've bled it twice and it's still doing it and heaters arnt that hot.. Air must be getting in but where I only took the stat out that's it...

Since replacing my thermostat today and bleeding the system well. My idle when in park just blips from 1500-2000 constantly.. My icv is whistling so I'm not sure if it's on way out?

This morning my car took awhile to warm up and after a 5 minuets stop to get fuel it took ages to rise only until I stopped it began to raise us this because of the cold wether and cause its sucking in colder air?? Either that could be a thermostat I suppose

Right guys, I've got a problem with my pcv valve. Now I like to do things for free and easy lol which will work well. 1. How do you gut the pcv.. 2 any other ideas as to how to use the existing pcv valve hole or after you have gutted it in different ways ie relocating it some where else. Any...