Search results

That is the S***S, go for it Dane. lol

You are of course quite correct, however if you look at the scales on either side of the page you will note that they are different. 0-220bhp against 0 - 180 lbft. If they were scaled the same, the figures would have crossed at 5252 as they should. From what I know about the Dastek it...

Latest offering, another 2.5 Impreza .

Thanks Dane, don't forget to keep me posted about yours.

Some of our latest offerings. My own 2.1 stroked Impreza with Turbo Technics T38 hybrid turbo. 1.6 bar boost on 97ron fuel. And a 2.5 Impreza with a Cosworth built motor and billet crank, modified heads and cams and other supporting mods. 1.8 bar VPower.

Hows this , NASP LS1 engine in TVR Sagaris pre Britcar 24 hr. After qualifying third it was written off during the rolling start. http://s40.photobucket.com/albums/e235/BonnieAmber/?action=view&current=work10006.flv

Whenever you are ready m8..

Unfortunately Danes car wouldn't take another few degrees, not without spitting its dummy out. I spent a bit of time with Dane asking exactly what he wanted from it, and reliability was paramount, with this is mind I have left it quite rich at the top end. With a reduction in charge temps and...

Dane all you had to do was ask m8, should have thought really, forum goers do like to know the ins and outs of a ducks ass..lol.. I did try it leaner in the spool stages but it just seemed to kill power, likes to be rich in the middle yours.

Sorry guys but you are all missing the point, there is far more involved with getting the numbers than the mapper. The quality of the supporting mods and the engine build are just as important as the quality of the tune.

Sorry guys , been away from the forums for a while and I have only just found this thread.... Gee have you considered trying to raise the octane content of your fuel , saving yourself some money and gaining power and torque to boot... Not a new thing I know but we have recently introduced...

Is that so , I think you should get your facts straight before pointing the finger , and remember that WE read forums too... We were asked to carry out an engine swap on the Focus nothing more , and everything went back on exactly as it came off after having the conversion carried out by Puma...

Very interesting little article in Japanese Performance a couple of months back that may be relevant here... Basic gist of it was that torque is very influenced by gearing , and that torque can always be altered with the correct ratios.... As Steve has a more track oriented car in mind I can...

The example dyno graph if you look in the top right hand corner says that it is for a Corvette Z06 , it is also in WHP not flywheel figures... There are plenty of dyno graphs of all sorts on our website in the dyno section.... www.enginetuner.co.uk

Looking good Gee...........! Lots of boost and it holds very well , looking forward to cranking Waynes up now...

No Gee , the Starlet does not have an inlet temp sensor from stock... The best place to fit charge temp sensors is in the intercooler pipework approx 6-12 inches from the inlet manifold... If you can mantain temps of below 40c your intercooler is working fine....

ALL rolling roads can only give an estimated flywheel figure...The losses tie in very well with what I would expect to see at this level.... As for tackling a GTti on DTA no problem , when you're ready give us a ring and we will book you in....

Your welcome anytime Dave , and we run an open house here so if anyone fancies checking us out feel free to pop in..... Martyn

Yes Dan we certainly can , we charge £240+vat as a rule for any first time map.. I choose to map on the rollers in a controlled envoirenment where I have £70,000.00p worth of equipment to tell me whats what , following this I take extensive road tests to check for det , driveability etc... I...

We map most aftermarket systems including the Power FC , Autronics , Motec , Gems , SimTek , Omex , Greddy E-Manage Blue and Ultimate , AEM , DTA and have more to come... Haltech and the brand new Unichip Q and Q+ are being looked at for the new year and we work quite happily with customers...