Search results

  1. B

    Need Assistance with gearbox

    I am in the proces of putting a 4age/gze in my glaza but i would like to reuse my original glanza gearbox with lsd and its mounts. I was told I could use the bell housing off a 4a or 4agze and mate it to the back half of the starlet gearbox. I want to know if this is possible, which starting...
  2. B

    Ignition Help Needed

    Can someone tell me what timing a stock 5efhe runs please. I have my timing map done but I am thinking that it is a bit low. I am willing to post a pic of it. Any help is appreciated. I just want a basis or guildeline as in how much i could possibly run.
  3. B

    5efhe Forged Rods What's the best brand to get.

    Came across these has anyone used them? Can't find any reviews online http://www.maxspeedingrods-store.com/Toyota-5EFE-connecting-rods-4-pieces-CR-TOY-5EFE.htm MAXSPEEDING rods.
  4. B

    Flywheels and clutches

    I was told that we can use the same clutch and pressure plate from vehicles such as the 20v 4age. Was also told we can use them from the 2zz-ge and that the same we we redrill the 4e flywheel to match the bolt patter of the 5e we can do the same thing with the 2zz-ge flywheel. Can anyone...
  5. B

    Radiators Questions

    Hi has any one ever used a triple core radiator as an upgrade as opposed to a double. I've had a double and it seemingly worked on unless i took it to the track for a couple laps. it would then start to overheat. And can a standard radiator work with those autobhan 88 styled exhaust...
  6. B

    Braking question.

    On my ep82 my brakes were perfect. From the time i touched the pedal the car would cut back good speed. The harder i pushed or lower to the floor the more braking power. Pedal never got near the floor. Thats how I like my brakes. In my EP91 with ABS it was the same thing as the abs doesn't...
  7. B

    EP91 Boost Question

    Does the standard ecu limit boost of a Glanza in first and second gear. Was told this by someone. My ct9 has no boost controller so I find it hard to believe. Its riged for high boost which is 9.whatever psi. But I'm running a 5efte so the ct9 fans out pretty darn early. I find that...
  8. B

    Ep91/

    Has anyone used the AUTOBAHN88 exhaust manifold for the ep82/ep91 T25 flange. http://cgi.ebay.com/ebaymotors/Toyota-Starlet-EP82-EP91-Exhaust-Manifold-T25-Flange-_W0QQcmdZViewItemQQhashZitem1c07ac9bf3QQitemZ120387836915QQptZMotorsQ5fCarQ5fTruckQ5fPartsQ5fAccessories#ht_3779wt_1165 Thinking...
  9. B

    New 5efte Build

    Driving around currently on 5efte (5efhe rods and block with stock unshaved 4efte pistons). Just purchased a second hand Thrust Greddy T517Z turbo, doesn't look much bigger than the Garret T28RS i had before. Does anyone know what flange this turbo carries been googling and coming up short...
  10. B

    Crx racing oil cooler kits

    Has anyone tried these kits off EBAY? I see a 16 row Universal kit for like 126 US. I am presuming this kit does not have the oil re-locator and do these thing screw right into the stock oil relocator...
  11. B

    HDI intercooler questions Doing Research.

    Hi all haven't posted here in a while. I previously had on two garret turbos 28r and 28rs with 2.25 intercooler piping fabricated to minimize the use of silicone hoses and clamps, estimate fabrication cost is like 500bds which is 250USD to mount an intercooler and get the piping ran and...
  12. B

    My New Glanza V

    Hi well I had a 1991 Gt Turbo Starlet and I've Upgraded to a 1998 Glanza V, Just thought I'd show some pics etc. ACT Heavy Duty Pressure Plate ACT 4 Puck Sprung Loaded Clutch ACT Throughout Bearing 2inch Intercooler Piping to be be upgraded to 2.25 HKS EVC 5 Boost Controller Turbonetics 7psi...
  13. B

    Brake Rotor Size

    What are the biggest size rotors the stock calipers can handle on a 15inch wheel? & What is the standard size disk rotor of an EP82? Can anyone assist?
  14. B

    Error Code 12

    I'm getting error code 12 which is No RPM Signal or TDC signal. My rpm gauge works fine. But the car doesnt go on limiter like a normal starlet. Was brought to my attention that this maybe why my timing is not being able to set properly. Any ideas?
  15. B

    Trottle Position Sensor Wiring

    Vehicle is a 1991 EP82 can someone tell me how the wiring goes for the TPS? Is it the red and yellow wire at top brown in the middle and grreen yellow wire bottom or is it red bottom green top brown in the middle. its the 3 pin square TPS model.
  16. B

    Engine timing

    Hi guys need some urgent help if anyone can assist. Recently put up a 5efte reused my old ep82 harness ecu etc yo guys know the drill. For some odd reason my engine wont keep standard timing. In order to get 10 Degrees on the pulley i find that my distributor has to be at full retard...
  17. B

    Speedometer issues

    Wasn't using one for a while finally bought a new speedometer cable and installed it. The prob is it reads wrong it skips and jumps up and read way more speed than what is actually being done. Any clues?
  18. B

    Need Advice Installing Electrical Oil Pressure Gauge.

    When instlaling an electrical oil pressure guage what is the best means of running the oil form the block to teh sender. Cant mout the sender directly on the block due ot lack of room and fear of the weight of it breaking it right out. I know steal braided line is the best option but can a...
  19. B

    BG suspention

    has anyone ever herad of them supposedly 30way adjustable coilover suspention for ep82/91 and tercels. Anyone know of them and any reviews. http://www.asia-race.com/order.html
  20. B

    Engine question

    How much psi can a GT turbo handle on stock internals running a Garrett GT28r and some form of management.
Top