Search results

  1. A

    Cap 4 puck

    IMHO I don't believe CAP clutches are still made however this ACT combination http://www.advancedclutch.com/tl1-hdg4 holds 265 foot pounds
  2. A

    Need info about headwork

    Compression wise personally I would not use 8.3:1 CR when you have very good pump gas available in your area and good ambient temps, the lowest I would use is 9.0:1 CR and if you add a water injection kit that is additional safety. 35 per cent improvement has been seen on a flow bench with...
  3. A

    Need info about headwork

    Head work can be very expensive, the Zisco modified heads use 7MGTE valves modified to fit the 5E heads and back in the day 4AG valves were used in the USA. You will need uprated valve springs: https://www.raceeng.com/p-19871-springtitanium-retainer-kit4e-fte-set-4e-fte-kit.aspx For cams these...
  4. A

    5efhe rods capabilty question

    yes sir it is running on corn liquor (E85)
  5. A

    Autometer Boost Gauge Fitting

    On my car I have the silicone hose connected to the gauge and the nylon pipe connected to the silicone hose
  6. A

    5efhe rods capabilty question

    No this was on a different car not Doug's car. Check this out https://www.youtube.com/watch?v=5u7OltMSU18
  7. A

    Autometer Boost Gauge Fitting

    You will need to use a piece of AN dash 3 silicone hose most speed shops sell this hose if not you can always try eBay
  8. A

    5efhe rods capabilty question

    The car was using a T3-T04 turbo and the hose came off the waste gate that is why car over boosted. The car was revving to 7300RPM
  9. A

    Td04

    If you can locate a flexible hose like the one in this link it may work? http://www.aliexpress.com/item/Car-Multi-Flexible-Extensible-Cold-3-inch-Air-Intake-Inlet-Pipe-Tube-Hose-blue/751663000.html
  10. A

    5efhe rods capabilty question

    Janki that is a pretty good list however personally I would use the 7MGTE Supra 440cc injectors and change the throttle body to at least the 55mm one from the Camry. The 5EFHE rods are fairly strong I have seen them bend on a 5EFHE engine that over boosted to 28PSI. When you have the engine...
  11. A

    Td04

    I use the Trans Adapt oil filter relocation kit part number TRD-1113. However I did not use the brass fittings or the hoses that come with the kit. I used Russell AN fittings and braided lines instead. One straight AN fitting and one 45 degree fitting
  12. A

    5efhe rods capabilty question

    Check this out: http://board.tercelonline.com/viewthread.php?tid=49650&goto=search&pid=582730
  13. A

    5efhe rods capabilty question

    Janki if you have gone to the trouble to buy the Arias forged pistons why not buy a set of steel con-rods? You can get a set of 5E steel connecting rods from CX Racing for USD 289.00 plus shipping and you can have a machinist make the small end of these rods fully floating and your engine will...
  14. A

    What do the Americans class our starlets when looking for parts

    If you have the part numbers you can usually have success getting the parts from1sttoyotaparts.com
  15. A

    trying to get some KYB SR Special dampers from Japan - anyone else?

    I had good results with KYB GR struts and Tein springs or you could try Stagg struts and Tein springs. A few guys here in the States who autocross use them with good results
  16. A

    twinturbo 4efte...

    I admire your thinking outside the box but exhaust energy-wise it would be better to have one turbo spooling the second one look at this photo in the link http://board.tercelonline.com/viewthread.php?tid=53311
  17. A

    Ignition leads/Spark plug wires Help!

    Four NGK plug wires for a 1995 Toyota Paseo and a coil wire for a 1996 Toyota Camry and you will be good to go.
  18. A

    Something different. A tale about a car lost and forgotten

    Truly dedicated and awesome work! I have one question which is why not use the front cross member for a '82 Corolla and fit the rack and pinion steering instead of the steering box?
  19. A

    Oil leak getting worse

    If it is the camshaft seal just buy a new camshaft seal for a 92 to 95 Paseo
  20. A

    EP82 in NYC

    Welcome to TGTT however parts are available in the USA. Any 4967 oil filter for a Camry fits the Starlet. For parts sources you can also check tercelonline.com
Top