Search results

Hey guys I need some help with these 2 solenoids am trying to figure out what they do and how they work if any of the 3 wires attached to ecu pinout?? thanks

Ok guys I need some input with this Buddy Club Brack Box questions will be at bottom On thread so have a look and post you inputs: Cases & stickers: Connections attach to ecu pinout & circuit board: Circuit Inside the lil black box: Stock ecu crystals: Brack box...

Ok bought a used engine earlier this yr as i could not get my car to past etest. engine came with G/box While inspecting I notice both when turning 1 axle the other axle turn the same direction , I then check My old g/box but only one wheel turn at at a time. Thinking My old g/box was...

Hey guys, am about to do a brake upgrade on my ep82 kit: wilwood forged dynalite and some 270mm x 22mm rotor from a mazda miata . I went this route as i wanted to keep my 15" wheels and overall cost under $600 cad . Already purchased the calipers and rotors, pads, lines. but now i need to...

hi guys am looking for a complete set of door locks & ignition lock (barrel) with key. so driver door ,passenger door, rear door & ignition (lock assembly/ barrel) + key to fit a 93 Ep82. Thanks

i need a ep82 floor Carpet in good conditon need one DESPERATELY!!! Thts the last thing i need to replace my burnt interior name your price + shipping asap Grimsby Ontario Canada L3M4E7 Thanks

hi guys as some of you might know my ep82 was stolen and recovered the inside was slightly burnt front seats and center console trims. i am tryin to fix her back up but i need to find a ( gear shifter gator boot, 2 peice center console that goes over gear stick and hand brake, and radio...

Thinking on setting up my td04l to run external wastegate : is it prossible to make a hole in the front of the manifold (facing front grill) and get a flange welded on or will it crack?? its a black speedvision td04l 3mm mild steel manifold.

Trying to change my timing belt & crank rear seal. 1. how the hell do i get the crank pulley bolt loose?? i dont have a locking tool, tried for hrs lastnite but crank turns everytime pissing me off. 2. can the rear crank oil seal be replaced without taking off oil pan? alsoif the oil...

hi guys i think my wheel bearing on front passenger side is gone , being humming like a hive of bees lately, i jack the car up this evening & rotate the wheel back and forth & i could hear lil crackling sounds like crush bearing balls. need to get it changed ,but i can't get the Huge nut off it...

hey guys my clutch is slipping really bad now so want to get a new kit. am thinking of buying the parts seperately to make my own kit. will these fit my 93 Ep82, 4E fte? ACT HD Pressure plate -212mm -Part# T022 ACT 6 pad clutch disk (not sure what mm) - part# 6212103 or 3000606 ACT...

hi guys just want some input on this 2 tpyes of piggy-back controllers have anyone ever run a MAP-ECU or MAP-ECU2 on a ep82 starlet? i hear they are better than a SAFC II . Am thinking of getting 1, just need some input, what you guys think? here is the website: http://www.mapecu.com Thanks

hi guys met an accident about a hr ago. some idiot drove out on me & to avoid writing-off my car run off the road catch some snow slide hit a hydro pole earthing wire and smashed my Rad,driver side quad light,bumper & grill. will this civic vtec Rad work...

Ok guy i took the car to get the tracking done, but they found a problem, so no tracking can be done until problem gets sorted. this is what they told me this evening: they said that the (Superpro blue poly bushing) that i installed in the lower front control arm is not fiting in the control...

hi guy having a bit of handling probs lately. jic coilover :Front 8k & Rear 7k front & rear :strut brace whiteline: F -24mm & R-22mm ARB's whiteline: Anti-lift casters superpro: poly bush recently i installed a whiteline 24mm front & 22mm rear ARB ,anti-lift casters, & some poly...

Hi guys need some help, car pissing me off. Ok car use to run fine before mod. mods:2.5" buddy club exhaust, k&n filter,toy tuning actuator, 225lph pump, turboxs fcd, weapon R fpr set to 45psi. Problems: 1. fuel cut, but after fooling around with the actuator it does backfire & pop...

hi guys i have 2 question about turbos. not sure if any1 ever think of any of this 2 route,might be stupid but i need to know, here goes. 1. CT9: could you use different turbine inducer & exhaust wheels with more blade on a CT9 turbo , say something like a 6 blade wheel pullin in & 12...

Hi guys am from canada i have an EP82 & its taking the piss outta me.its fairy stock except for the recent addition of a straight through 2.5" stainless steel exhaust other mods just k&n air filter, turbo timer, volt stabilizer,quad lights conversion & some handling mods thts it. Now to my...

hi guy i know this sound stupid , and i feel even more stupid asking, but does any know how much a set of 4 Tein Flex coilover for ep82 weigh in kg's? just need to know if it over or under 10kg. any help appreciated. Thanks