Search results

Anybody know the torque spec for the sump bolts... not the sump plug? I checked the workshop manual and searched the forum but couldn't see anything... I always seem to swing a bit too much and snap one =(

anyone have an o2 sensor for ep82? or know where to get one?

Need a map sensor for a 94 ep82

Hello, as above Im looking for the 3 bar map sensor to fit the emanage and some 550 injectors...or thereabouts... regards Anthony

Looking for an Emanage blue or ultimate or standalone if its cheaper... cash waiting please let me know!

Can somebody tell me what oil temps theyre getting when warm? Mine seems a little on the cool side, I dont think my oil thermostat (for my oil cooler) is working as it should. Also, are there any effects on turbo or engine when running too cool? Cheers Ant

Hello folks! I'm looking for some help... running a forged td04 on an AEM FIC... its already been mapped with a pretty good result... but I have an issue ...sometimes the car fuels completely wrong.. take this log recorded at idle for instance... look at the crazy spikes in AFR! And this...

as above looking for an e-manage blue or ultimate thanks

Hello guys, had my car mapped the other week at TDI-NORTH Warrington... according to the dyno the results are... 238.1 bhp & 215.2 lbft 1.1bar 258.9 bhp & 232.6 lbft 1.3bar Mapped on AEM F/IC Car engine spec is as follows... Forged 4E Rebuilt TD04L Turbo Front Mount Intercooler Front Mount...

Hello guys, had a problem for a long while now, my car will just cut out sometimes if i stick it in neutral or have my clutch down when coming to a stop... not all the time but quite often it will happen. I've got a new dizzy cap and rotor arm here which Im going to change tonight, but just...

Anyone know what operating temp is for oil? And also what oil temps should I start to worry about? Using 10 40 Thanks

First off... I have one of these thermostats.... http://www.rallynuts.com/take-offs-oilstats/mocal-in-line-oil-stats-push-on.html My oil cooler kit uses braided hoses.... will a strong hose clip be strong enough to use on braided hose over this thermostat? (pressure wise) And also how...

Hello guys, my spec is as follows... Forged 4EFTE TD04L Front Mount Intercooler Front Mount Air Filter AEM FIC Toyosport Mildsteel Manifold Toyosport Mildsteel Decat Front Exit Exhaust 255 LPH Fuel Pump Looking to run TD04L at 1.2/1.3 bar and hit around 220-230bhp I have 330cc injectors but...

Can anyone tell me if these will fit 4efte.... http://www.ebay.co.uk/itm/280710556223?ssPageName=STRK:MEWAX:IT&_trksid=p3984.m1423.l2649

Hello, I have one of these oil cooler + relocation kits... http://www.ebay.co.uk/itm/STARLET-GLANZA-12-ROW-OIL-COOLER-RELOCATION-KIT-TURBO-/180708838904?pt=UK_CarsParts_Vehicles_CarParts_SM&hash=item2a13160df8 problem is I cannot fit this anywhere, the only way I can get it to fit Is on...

looking for any of the above, must be good condition!

My car when coming to a stop will sometimes just cut out...even if i put it into neutral or put my clutch down before stopping it will just die... any ideas...? running a forged engine with blitz active clutch + flywheel..

Hello guys, have managed to break a connector under the engine bay, just wondering if someone can tell me what it does... it sits to the back of the engine, drivers side, just to the left of the brake master cylinder.. thanks Anthony sorry this should be in electrical, can this be moved please...

Hello, I have oil pressure and temp gauges from prosport that allow you to set a warning when the pressure and temp hits a certain value... can anyone tell me what would be considered too low oil pressure and too high oil temp so i can set these warnings? Thankyou

Hello guys, have a 4efte running 1 bar with front mount intercooler, front mount air filter and blitz super sound dump valve. I get the chatter noise with this setup... if i put on the standard top mount intercooler setup it stops... can anyone tell me first of all why this is...