Search results

Hi lads i have a bit of a problem, me stupid engine is leaking and i dont know wat it could be, its had a head skim and block skim and brand new athena head gasket and its still leaking oil from between the head and block left hand side just above the oil filter housing, i dont know what it...

Just wondering can you use a sandwich plate to get the turbo oil feed or must you use the 4e oil filter housing? I have the sandwich plate all ready so im just wondering what to use, thanks.

Hi my heads in the shop getting a few things done and they just rang saying there is to much of a gap between the cams and the buckets, they have fiitted cruise springs also, its a 5e head with 4e buckets. any help is appreciated, Thanks lads.

hi lads having a problem wit da ignition when i turn the key to the on possition the car trys to start her self and no dash lights, and when i turn da key to the place where you swing it to start the car it wont start da dash lights just come on like they should when the key is turned to on...

hi lads car is giving wicked trouble :mad: and im trying to get it ready for enniskillen, i cant get it to tick over below 1250rpm,more importantly she splutters like mad when it comes to around 6500rpm onwards,so i cant get full power out of her nw iv changed every thing i can think of...

hi as i said she wont go into first and a bit hard at times to go into reverse, just changd the selector there and still the same problem, cables are grand lookin. i just put the gearbox in after changing the bell housing, could i of forgotten somethink or broke somthink ??.. wat can i do to...

hi as i said the car wont take boost in 2nd,3rd,4th,5th. she hits full boost in first no bother to her then i bang 2nd and she brakes down and starts to hold her self back then shel clear up after 6k then do the same thing the next gear, please help me on this as need car going for the up and...

hi does any one no any thing about these? what there like on glanzas ect, i can get one for 100 euro and it il bolt on to my mani and decat.(TD04 mani,decat) thanks

Well its ticks over fine until i just tip the accelerater then it starts to tick over like theres a vac pipe off i checked the vac pipes and none are off also checked intercooler and its good. And i was thinking if it was a vac pipe wudnt it tick over bad the hole time? Not just when i tip the...

hi does anyone no were i can get upgraded drives for a glanza?

Spraying da drag car Wat do ye think black or white?

Hi im gettin a set of 13x10 wellers i can get them in a plus or minus 24. Just wondering what you think i should go for? Keeping in mind Glanzas need 13mm spacers to fit 13s.

hi just wondering wil these brakes fit my glanza there 254mm x 18mm centre bore is 55mm.just thsy say non turbo but think there the sme size , if some one could just confirm it please, thanks...

hi im lookin for da bare engine 5efe or efhe. what ever you got. thanks

im looking for coilovers for my drag boxy, im looking to lower it at the front and raise it at the back, i can get tein coilovers for 350euro does anyone no if these will b able to go low enough? i dunno wat type they are, but i here teins only go 40mm. do you think 40mm wud be enough , 40mm low...

(keeping in mind the cars only used for drag racing) i could use a bit of help on this should a turbo car be long ratios or short? because the 4 speed was put in last nite, i thought the gears were going to be longer like say 180km in 3rd which is wat i heard they do but instead its like...

hi i kinda broke my gearbox last nite, luckly had a 4speed lyn around just wondering could i fit a levin final drive into it.??? i only use the car for drag racing. just wondering wat sort of top speed id have, would i be hitting the limiter in 4th before the end of the race. thanks.

can anyone shed some light on this..im doing a conversion was thinking of keeping the boxy hubs on it instead of putting on the rear disks. id just use drilled and groved on the front. do ya think it will stop??:haha:.

hi i have a glanza da bodys ruff and i want 2 build a drag car so i bought a ep70 to do a conversion, now iv been looking it up on da site and all i can c is ep82 to ep70 conversions, will da glanza parts not fit da same as da gt ones????? any help on this topic will be grate, thanks lads.

another grate day of racing, won all my races grate beating all da hondas,a 450 cc quad, and 2gts bar 1 fool who i hear is saying he beat me on honda haven, nw it was my first race and wasnt boostin rite (only .7) and it was close but still beat him by a foot id say but wining is wining. wen i...