Search results

Iv just bought one of these of member of here want to know should I run water lines with this turbo at around 1.3 or 1.4 bar boost tuning developments say to use them so I'm inclined to but iv heard from others not to had anyone any advice here. Also any other information people have on turbo...

As above lads can't seem to find a definite answer. Is it 60nm in 3 equal turns?

As above lads it will be a few months but I think I'm going to forge an engine. What turbo would be best for near 300bhp. I seen a lot about td04 what one is best for minimal lag fun to drive and for drag also looking for a clutch to run the same power if anyone has any advice on where or what...

Can anyone send me the link or tell me how to set up tps. Since I fitted new engine car is idling at 1800 when worm . Is it tps or air idle control valve my problem?

As above lads fitted my ct9 wepr power up kit today and is blowing out between mani & head at bottom of mani. Went for a drive and car is not starting to boost till 3000rpm and by 5500 it's spiked right up to 1.1 or more. Need advice as I have no experience with external set up. I welded d...

As above must be perfect workin order.

Wel lads will be rotating my tongs hybrid (for short route) at sum stage and welding waste gate shut. what are the turbo like to do any tips or how to guides up? Do I just put a spot weld on it or do I weld it all round? I heard about brackets to hold them shut as well? If anyone has any tips or...

Hoping to forge my 4e soon and map it on a tongs hybrid with an emu for now till I get a big turbo. Just woundering is there many lads using forged gt or glanzas daily or any lads with big millage forged engine have you had any problems what are they like reliability wise. I will be using...

as above lads

wel lads as above lookin for short route hotpipe from turbo like the one in the bottom of this fs thread. need one asap http://www.toyotagtturbo.com/forums/showthread.php?99020-ct9-turbo*zisco-decat*short-route-intercooler-pipe*exedy-clutch*leads*-more-for-sale

as above lads i think my front mount is a hdi one looks like the one in my link. would like to get one in ireland if possiable and i was wondering will it fit in by the two pipes going to power steering pump. my i/c pipes go over the mani i want the 1 that go's up by the power steering pump...

well lads what oil or where would i get oil in ireland for a kazz 1.5 way diff

as above lads what are these like on road use? are they a good diff in general

i have cracked two different manifolds? i cracked a mild steel wepr one and a stainless steel one i cant understand why? Everyone told me wepr are the best but why do mine keep cracking? the mild steel one i had on the car for a long time before it cracked but the stainless steel one was only...

well i just got my gt lowered abit more and its not mad low or anything i'v seen gt's alot lower but its rubbing the archs over speed ramps or bumps in the road and cornering hard its on nearly new bc coilovers and i have an adjustable panard rod and just had tranking and camber set. anyone else...

what size belt do i have to get for a gt wit the air conditioning removed and where can i get it need 1 asap.

well lads might be buying one of these just wondering do the stainless steel manifolds crack or warp much, or more then a mild steel one?

i'm getting no positive boost reading from my car me ebc wont read past -6 KPA boost could this be my solenoid. its lyk driving a dead non turbo starlet. this happened when my mani started blowing out badly but got it sorted and still no boost??

as above lads needed asap

well lads have a gt running about 200bhp with a ct9 hybrid turbo hear is some of my mods just woundering what other mods i could get dat wont coast a bomb to improve bhp Blitz nur exhaust system decat manifold hybrid turbo air filter relocation kit rocker cover breather...