Search results

  1. dark_knight

    Look what I found...

    Is the screw loose.. able to flap about..? If not, it may have been screwed in there to bung a leak.. :)
  2. dark_knight

    Ignition coil.. boost solenoids etc please read

    Too bad I'm too far away to be of any help.. :rolleyes:
  3. dark_knight

    Seeking Alternatives: Throttle Position Sensor for EP71 4EFTE Engine

    Do you want a linear TPS or just the clicky on/off-switched ones used on the manual trannied models..?
  4. dark_knight

    Standard resistance values for a distributor coil

    Distributors will generally wear out from age and corrosion from the high voltage going through it all the time it's in use. Open it up and share some pictures perhaps..? Also, you've mentioned the coil and the distributor.. so which is it..?
  5. dark_knight

    Anyone running the ME221 ECU from Motorsport electronics?

    Greetings earthlings.. Sorry, I got a little too fat over Christmas from eating all the treats and couldn't do any sort of work due to sheer laziness.. hehehe Now I'm back and still cleaning up lots of electricals as the engine management was just but a slice of the larger tasks getting done on...
  6. dark_knight

    Rear brake line clips

    We see what you did there.. :D
  7. dark_knight

    TPS 3 Pin/4 Pin Voltage Output

    See if you can pick up some hints from this build album. Did it sometime in the year of the Lord 1623 Before Christ.. :D https://goo.gl/photos/xBDFv4PzEN1oTc48A
  8. dark_knight

    Driveshaft ep82

    All true.. hence my comment on bravery.. :) At times, you just need to get home or to the next shop where you can get a proper job done. I got to discover this at some point when I needed the rig running for a tarmac race event.. and no one had the inboard CVJ boots in stock. We got the closest...
  9. dark_knight

    Driveshaft ep82

    You can also use some decent worm-gear clamps snipped to just the right size if you are brave enough.. :D
  10. dark_knight

    Piggyback or Stand Alone in 2023

    Pics.. content.. guides please.. :) Always nice to see what other folks out here are doing.
  11. dark_knight

    How to fix issue with GT Tacho not working.

    This is assuming your tacho just dies a natural death.. and was not tinkered with before dying.. right..? :)
  12. dark_knight

    TPS 3 Pin/4 Pin Voltage Output

    The 3-pin is a switched (on/off) 12-volt DC signal. The 4-pin is what varies the 5-volt VCC signal.
  13. dark_knight

    Piggyback or Stand Alone in 2023

    Seems like good advice.. especially about the trouble-to-set-up bit.. :)
  14. dark_knight

    Piggyback or Stand Alone in 2023

    Haltech money is house-purchasing money for most people.. :p .. but as you said, worth it every time..
  15. dark_knight

    Anyone running the ME221 ECU from Motorsport electronics?

    Aha. I'm already on the CoP upgrade. Here's a WiP build album that I've not updated in a long minute.. but should give some insight for those who want to go the same route. I'm a cheapskate like that so reusing a lot of OE parts, even from other vehicles. Coils from Toyota. Harness plug...
  16. dark_knight

    Drain fuel

    While on the topic, how long is too long for fuel to go bad.. and yes yes.. I know, the environmental variables matter but in general, how long would you folks say is too long.. especially for you Ukay boys and girls with your 11.5-month wet weather life.. :p
  17. dark_knight

    Anyone running the ME221 ECU from Motorsport electronics?

    @Glanza_Muzz , what coils are you running on your setup..?
  18. dark_knight

    Anyone running the ME221 ECU from Motorsport electronics?

    Yes, the wideband needs to go on the board directly. By now, we can all agree nothing aftermarket is plug-&-play, even when they say it is.. hehehe :cool: Care to share any images from your install..? Some cheat codes for you if you need. The onboard connector is compatible with any of the...
  19. dark_knight

    Anyone running the ME221 ECU from Motorsport electronics?

    Well then. Fair warning as I'm just getting to this stage of the build. I've shaved down the two teeth so wish me luck. The ME221 ECM that I have was running on an engine before it came to me so I'm pretty confident that it will work for me as well. My dizzy before the butcher arrived.. :D...
Top