For sale: Forged TOM'S EP82
Item Condition: Good Condition
Price and price conditions: £4995
Extra Info:
If this doesn't sell I will sell all the parts in a separate thread.
ENGINE
Built by KAD
Block Chemically Cleaned
0.5mm Overbore
Cross Hatch Honed
ROSS Pistons (Custom Dish)
PAUTER Rods
ARP Connecting Bolts
ACL Race Bearings (Full Set)
Blueprinted Bottom End
Ported and Polished Cylinder Head (Rebuilt With Genuine Toyota Gaskets and Seals)
3 Angle Valve Seats
Combustion Chambers Smoothed
Speedvision Valve Springs (Seated Lower in the Head where they should be)
Cruise 1.4mm Metal Headgasket
Head and Block Faced
Compression Ratio 7.8:1
ARP Head Bolts
Power Enterprise Kevlar Cam Belt
Tuning Developments Vernier Adjustable Cam Pulley
Race Spec Rocker Cover
TD04L
WEPR Manifold
WEPR Down Pipe
Braided oil and water lines
HKS Actuator
Blitz Nur Spec Exhaust System
WEPR FMIC
WEPR Hard Pipe Kit
HKS SSQV Dump Valve
Lightened Crank Pulley
Lightened Powersteering Pulley
Toyota Oil Pump
Toyota Water Pump
SARD Low Temp Thermostat
Denso Distributor Cap
Larger Battery
Custom Oil Catch Can
Apexi Power Intake (Mounted Next To FMIC)
Viper Red Silicon Pipes
Tuning Developments RRFPR
TRD Engine Mounts
Dual Core Alloy Civic Radiator
Revotec Slimline Fan
TRANSMISSION
ORC 309 Racing paddle clutch
ORC Lightened Flywheel
Standard Reconditioned Gearbox (Fresh oil 6 months ago)
BRAKES
Mintex 1155 Track Pads
3G Grooved Discs
EARL'S braded brake lines
DOT 5.1 Fluid
SUSPENSION
D2 Coilovers (2008 model)
CUSCO Carbon Front Strut Brace
Super Flex Poly ARB Droplink Bushes
WHEELS & TYRES
TOM’S High Action Wheels
Toyo PX4 Tires
EXTERIOR
TOM’S Front Bumper
TOM’S Front Grill
TOM’S Side Skirts
TOM’S Rear Spats
TOM’S Rear Spoiler
GI Bonnet
INTERIOR
GReddy Profec Boost Controller
JAM ECU
Blitz Carbon Boost Gauge
AEM Wideband Lambda Gauge
Carbon Fibre Centre Console Insert
M3 Steering Wheel and Boss Kit
Razo Gear Knob
TRD Gauge Cluster
Sony Headunit (iPod connection)
I’m very reluctantly selling my car to get a deposit for a house. I’ve owned it for 8 years and have spent far too much money on it (over £15,000). I’ve always bought the absolute best parts for it and made sure they’re all set up properly, which has made sure the car has always ran like a dream. I service the car myself and have fitted almost every part as I haven’t found a mechanic with as much attention to detail as me. The car is washed, polished and waxed every 2 weeks and is kept in a garage every night without fail.
The car has never let me down, always started first time and never over heated or run low on oil. I always use Millers fully synthetic oil and Toyota for life red coolant. The forged engine was installed in March 2010 and was run in on Millers running in oil (changed after 10 miles, 300 miles and 600 miles and then to fully synth at 1000 miles).
When I got the car it had the full genuine TOM’S kit, JAM ECU, Blitz Nur Spec Exhaust, HKS SSQV and Blitz Carbon boost gauge installed. Since then I have bought and added all the parts above, almost all of which have been brand new. The first round of tuning I did was to install the HKS actuator and get rid of the EFI pipe by making up a front mount intake with a HKS mushroom filter and ported the wastegate and 3rd manifold runner. The next round of tuning was a WEPR FMIC, hard pipe kit and Blitz Dual SBCR boost controller. After setting up the boost controller the clutch started to slip so I bought the ORC 309 clutch and flywheel kit and had this fitted with a set of lightweight under drive pulleys, TRD engine mounts and a cruise 2mm head gasket. I ran this for about a year until I put the TD04 kit on and the AEM wideband gauge. I then ran the TD04 setup for about a year until the car started to puff a bit of smoke which turned out to be down to the valve stem seals. I had the feeling the block could do with a rebore and hone so I decided to go all out and research all the parts needed to build the best 4EFTE. I chose the Ross pistons as they have the lowest silicon content of all the pistons I could find available for the 4EFTE and therefore should be the strongest and I chose the Pauter rods as they have the highest pressure and rpm rating of all the rods I could find for the 4EFTE. ACL bearings and ARP bolts have a fantastic reputation in motorsport and the only realistic option for cams and springs were speed vision items. I gave all of these parts to KAD and they carried out the build for me, blueprinting the block, porting and polishing the head, rebore/honing/facing the block, working out perfect clearances for the valve train, measuring and adjusting the compression ratio etc etc. I’ve had the car back up and running for almost 4 years now and it hasn’t missed a beat, it’s a very strong engine and I built it with the intention of running 350+bhp however my priorities have changed and I’m now looking to buy a house and will be needing the money from this sale to help fund that.
Pictures:
Location: Kent
Contact Details: PM Me
Pick up Only
Item Condition: Good Condition
Price and price conditions: £4995
Extra Info:
If this doesn't sell I will sell all the parts in a separate thread.
ENGINE
Built by KAD
Block Chemically Cleaned
0.5mm Overbore
Cross Hatch Honed
ROSS Pistons (Custom Dish)
PAUTER Rods
ARP Connecting Bolts
ACL Race Bearings (Full Set)
Blueprinted Bottom End
Ported and Polished Cylinder Head (Rebuilt With Genuine Toyota Gaskets and Seals)
3 Angle Valve Seats
Combustion Chambers Smoothed
Speedvision Valve Springs (Seated Lower in the Head where they should be)
Cruise 1.4mm Metal Headgasket
Head and Block Faced
Compression Ratio 7.8:1
ARP Head Bolts
Power Enterprise Kevlar Cam Belt
Tuning Developments Vernier Adjustable Cam Pulley
Race Spec Rocker Cover
TD04L
WEPR Manifold
WEPR Down Pipe
Braided oil and water lines
HKS Actuator
Blitz Nur Spec Exhaust System
WEPR FMIC
WEPR Hard Pipe Kit
HKS SSQV Dump Valve
Lightened Crank Pulley
Lightened Powersteering Pulley
Toyota Oil Pump
Toyota Water Pump
SARD Low Temp Thermostat
Denso Distributor Cap
Larger Battery
Custom Oil Catch Can
Apexi Power Intake (Mounted Next To FMIC)
Viper Red Silicon Pipes
Tuning Developments RRFPR
TRD Engine Mounts
Dual Core Alloy Civic Radiator
Revotec Slimline Fan
TRANSMISSION
ORC 309 Racing paddle clutch
ORC Lightened Flywheel
Standard Reconditioned Gearbox (Fresh oil 6 months ago)
BRAKES
Mintex 1155 Track Pads
3G Grooved Discs
EARL'S braded brake lines
DOT 5.1 Fluid
SUSPENSION
D2 Coilovers (2008 model)
CUSCO Carbon Front Strut Brace
Super Flex Poly ARB Droplink Bushes
WHEELS & TYRES
TOM’S High Action Wheels
Toyo PX4 Tires
EXTERIOR
TOM’S Front Bumper
TOM’S Front Grill
TOM’S Side Skirts
TOM’S Rear Spats
TOM’S Rear Spoiler
GI Bonnet
INTERIOR
GReddy Profec Boost Controller
JAM ECU
Blitz Carbon Boost Gauge
AEM Wideband Lambda Gauge
Carbon Fibre Centre Console Insert
M3 Steering Wheel and Boss Kit
Razo Gear Knob
TRD Gauge Cluster
Sony Headunit (iPod connection)
I’m very reluctantly selling my car to get a deposit for a house. I’ve owned it for 8 years and have spent far too much money on it (over £15,000). I’ve always bought the absolute best parts for it and made sure they’re all set up properly, which has made sure the car has always ran like a dream. I service the car myself and have fitted almost every part as I haven’t found a mechanic with as much attention to detail as me. The car is washed, polished and waxed every 2 weeks and is kept in a garage every night without fail.
The car has never let me down, always started first time and never over heated or run low on oil. I always use Millers fully synthetic oil and Toyota for life red coolant. The forged engine was installed in March 2010 and was run in on Millers running in oil (changed after 10 miles, 300 miles and 600 miles and then to fully synth at 1000 miles).
When I got the car it had the full genuine TOM’S kit, JAM ECU, Blitz Nur Spec Exhaust, HKS SSQV and Blitz Carbon boost gauge installed. Since then I have bought and added all the parts above, almost all of which have been brand new. The first round of tuning I did was to install the HKS actuator and get rid of the EFI pipe by making up a front mount intake with a HKS mushroom filter and ported the wastegate and 3rd manifold runner. The next round of tuning was a WEPR FMIC, hard pipe kit and Blitz Dual SBCR boost controller. After setting up the boost controller the clutch started to slip so I bought the ORC 309 clutch and flywheel kit and had this fitted with a set of lightweight under drive pulleys, TRD engine mounts and a cruise 2mm head gasket. I ran this for about a year until I put the TD04 kit on and the AEM wideband gauge. I then ran the TD04 setup for about a year until the car started to puff a bit of smoke which turned out to be down to the valve stem seals. I had the feeling the block could do with a rebore and hone so I decided to go all out and research all the parts needed to build the best 4EFTE. I chose the Ross pistons as they have the lowest silicon content of all the pistons I could find available for the 4EFTE and therefore should be the strongest and I chose the Pauter rods as they have the highest pressure and rpm rating of all the rods I could find for the 4EFTE. ACL bearings and ARP bolts have a fantastic reputation in motorsport and the only realistic option for cams and springs were speed vision items. I gave all of these parts to KAD and they carried out the build for me, blueprinting the block, porting and polishing the head, rebore/honing/facing the block, working out perfect clearances for the valve train, measuring and adjusting the compression ratio etc etc. I’ve had the car back up and running for almost 4 years now and it hasn’t missed a beat, it’s a very strong engine and I built it with the intention of running 350+bhp however my priorities have changed and I’m now looking to buy a house and will be needing the money from this sale to help fund that.
Pictures:
Location: Kent
Contact Details: PM Me
Pick up Only
Last edited: