either full car for £8000 or strip of all parts. but need buyers for all parts before any stripping will take place otherwise i'll keep until ive had my fun with it.
check my members garage for spec etc or pm me or msg this thread.
thanks ian
*Section Engine Damper * £120 *
550cc Injectors £100
NGK Plugs Iridium forged engine £1600 *
Ross Forged Pistons
Pauter Rods
Cruise Valve Springs
NST Crank Pully
ACL Bearings
Fully race balanced
Engine work
Service cylinder head
Replace all valve guides
Service and replace (as necc) valves,lap and vacuum test.
Surface grind head face 0.005”
Strip,prepare,wash and rebuild with new stem seals and springs
Short motor assembly
Rebore to pistons supplied
Surface grind block face by 0.005”,polish crankshaft,
race balance to crankshaft/flywheel/clutch/connecting rods and pistons
gap piston rings to rrr turbo specification
prepare, wash and rebuild
Fit front cover and rear oil pump (supplied)
Acl main bearings
Acl b/e bearings
Acl thrust washers*
brand new ihi vf34 turbo heat painted
wepr td04 mani with external wastegate plumbed back to decat double heat wrapped
front mounted greddy oil cooler and relocation kit (to go on) £280
Emanage ultimate (to go on)
turbosmart external wastegate
custom meshed front mounted funnel (to go on)
custom intercooler kit reflective wrapped
spal slimline fan
Hks ssqv 2
Sard cooling plate (for sale soon) £35 *
Japspeed stainless exhaust system double wrapped in thermotec copper wrap £300 *
Ngk grade 7 plugs
Magnecore 8.5mm leads
sard header tank (to go on)
sard thermostat (to go on)
Blitz dsbc type r boost controller (just got it back so it needs setting up soon) NICK!!! lol
Manual boost controller (temporary until ebc is returned)
Set to 0.98 bar
speedo converter (to go on)
straight cut gearbox and aftermarket diff (to go on) £600 *
fidanza lightweight flywheel (to go on) £280
exedy paddle clutch (to go on) £300
SUSPENSION AND CHASSIS
Tein flex coilovers £350 *
3G/Wilwood 280mm big brake kit £550 *
Full roll cage with carbon crumple bars £500 *
Whiteline Front anti roll bar 24mm £100 *
Whiteline Rear anti roll bar £100 *
Whiteline anti lift kit £30 *
RSR panhard rod £80 *
Ultra racing front 4 point lower arm bar
Ultra racing rear lower arm bar
Zep c pillar bar £80 *
Zep 3 point rear strut brace £280 *
Zep cross bars £250 *
tanbe front strut brace £100
15" Rota jmags wrapped in yokohama parada spec 2s
uprated trd twist beam, lower arm front (to go on my new lower arms) £130
polyflex engine mounts (to go on)
INTERIOR
Recaro sport seats (out of an evo 7)
semi stripped rear
Luke 4 point harnesses £70
Momo steering wheel (advance edition)
Razo aluminium gearknob
Triple A pillar pod
Double dash pod
Stack AFR gauge
Stack boost gauge in bar
Stack oil pressure gauge
Stack oil temp gauge
Stack water temp gauge
Clarion cd/mp3 player with hard drive
4" Kicker components
Kicker kx75 2 channel amp
Jbl GT 2 channel amp on custom amp box
kicker 12" sub in custom enclosure
Harmon Kardon Ipod connectivity adapter
EXTERIOR
Custom rear bumper to make a euro plate fit and also smoothed the slats in each side for a more unique look.
Cut out and smoothed front bumper so no restrictions are in place of the fmic.
Also the whole bottom half of the car has been sprayed a newer and more unique grey colour.
Jam reverse scoop *
Toms grill (strengthened) £140 *
Front carbon splitter £200 *
custom rear diffuser *
check my members garage for spec etc or pm me or msg this thread.
thanks ian
*Section Engine Damper * £120 *
550cc Injectors £100
NGK Plugs Iridium forged engine £1600 *
Ross Forged Pistons
Pauter Rods
Cruise Valve Springs
NST Crank Pully
ACL Bearings
Fully race balanced
Engine work
Service cylinder head
Replace all valve guides
Service and replace (as necc) valves,lap and vacuum test.
Surface grind head face 0.005”
Strip,prepare,wash and rebuild with new stem seals and springs
Short motor assembly
Rebore to pistons supplied
Surface grind block face by 0.005”,polish crankshaft,
race balance to crankshaft/flywheel/clutch/connecting rods and pistons
gap piston rings to rrr turbo specification
prepare, wash and rebuild
Fit front cover and rear oil pump (supplied)
Acl main bearings
Acl b/e bearings
Acl thrust washers*
brand new ihi vf34 turbo heat painted
wepr td04 mani with external wastegate plumbed back to decat double heat wrapped
front mounted greddy oil cooler and relocation kit (to go on) £280
Emanage ultimate (to go on)
turbosmart external wastegate
custom meshed front mounted funnel (to go on)
custom intercooler kit reflective wrapped
spal slimline fan
Hks ssqv 2
Sard cooling plate (for sale soon) £35 *
Japspeed stainless exhaust system double wrapped in thermotec copper wrap £300 *
Ngk grade 7 plugs
Magnecore 8.5mm leads
sard header tank (to go on)
sard thermostat (to go on)
Blitz dsbc type r boost controller (just got it back so it needs setting up soon) NICK!!! lol
Manual boost controller (temporary until ebc is returned)
Set to 0.98 bar
speedo converter (to go on)
straight cut gearbox and aftermarket diff (to go on) £600 *
fidanza lightweight flywheel (to go on) £280
exedy paddle clutch (to go on) £300
SUSPENSION AND CHASSIS
Tein flex coilovers £350 *
3G/Wilwood 280mm big brake kit £550 *
Full roll cage with carbon crumple bars £500 *
Whiteline Front anti roll bar 24mm £100 *
Whiteline Rear anti roll bar £100 *
Whiteline anti lift kit £30 *
RSR panhard rod £80 *
Ultra racing front 4 point lower arm bar
Ultra racing rear lower arm bar
Zep c pillar bar £80 *
Zep 3 point rear strut brace £280 *
Zep cross bars £250 *
tanbe front strut brace £100
15" Rota jmags wrapped in yokohama parada spec 2s
uprated trd twist beam, lower arm front (to go on my new lower arms) £130
polyflex engine mounts (to go on)
INTERIOR
Recaro sport seats (out of an evo 7)
semi stripped rear
Luke 4 point harnesses £70
Momo steering wheel (advance edition)
Razo aluminium gearknob
Triple A pillar pod
Double dash pod
Stack AFR gauge
Stack boost gauge in bar
Stack oil pressure gauge
Stack oil temp gauge
Stack water temp gauge
Clarion cd/mp3 player with hard drive
4" Kicker components
Kicker kx75 2 channel amp
Jbl GT 2 channel amp on custom amp box
kicker 12" sub in custom enclosure
Harmon Kardon Ipod connectivity adapter
EXTERIOR
Custom rear bumper to make a euro plate fit and also smoothed the slats in each side for a more unique look.
Cut out and smoothed front bumper so no restrictions are in place of the fmic.
Also the whole bottom half of the car has been sprayed a newer and more unique grey colour.
Jam reverse scoop *
Toms grill (strengthened) £140 *
Front carbon splitter £200 *
custom rear diffuser *
Last edited:
