Home
Forums
New posts
Search forums
What's new
New posts
New profile posts
Latest activity
Members
Current visitors
New profile posts
Search profile posts
Log in
What's new
Search
Search
Search titles only
By:
Current visitors
New profile posts
Search profile posts
Menu
Log in
Install the app
Install
Home
Members
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
Frankieflowers's latest activity
Frankieflowers
replied to the thread
4EFE Crank VS 4EFTE.
.
It’s a 4E crankshaft. I cannot find a FE crank.
Tuesday at 10:55 AM
Frankieflowers
replied to the thread
4EFE Crank VS 4EFTE.
.
Hello. I am in the same situation in 2025. Got a 4E crankshaft going in its OE 4EFE block with all 4EFTE forged parts, uprated springs...
Jun 26, 2025
Frankieflowers
reacted to
Llawgoch's post
in the thread
4EFE Crank VS 4EFTE.
with
Like
.
every crank is hollow mate. they carry the oil inside to feed the conrod bearings. and also the 4efe cranks of 1998 onwards are marked...
Jun 26, 2025
Frankieflowers
reacted to
sx_turbo's post
in the thread
4EFE Crank VS 4EFTE.
with
Like
.
tolerances should always be checked before fitting any crankshaft, even if it came out of the same block.
Jun 26, 2025
Frankieflowers
replied to the thread
Forged bits, brands and engine build advice
.
Unfortunately, I don’t have the two cranks side-by-side.I am pretty sure that if they named it differently, there is a difference, but I...
Jun 25, 2025
Frankieflowers
reacted to
SKINY's post
in the thread
Forged bits, brands and engine build advice
with
Like
.
Hey Frankie, have you the 2 cranks side by side ? Could always measure the rod gaps etc and see if they are any wider ? Probably no...
Jun 25, 2025
Frankieflowers
replied to the thread
Forged bits, brands and engine build advice
.
My cylinders have been bored to 74.5 mm so CR went up. Consider that Wossner flat head pistons in a stock scenario bring the CR up by...
Jun 20, 2025
Frankieflowers
reacted to
dac69er's post
in the thread
Forged bits, brands and engine build advice
with
Like
.
0.051" cometic head gasket and flat top pistons. Estimated approx standard cr
Jun 19, 2025
Frankieflowers
replied to the thread
Forged bits, brands and engine build advice
.
Hi! What CR and HG did you end up choosing?
Jun 8, 2025
Frankieflowers
reacted to
Jay's post
in the thread
Forged bits, brands and engine build advice
with
Like
.
Don't think I've seen any local guys use flat-top pistons, probably more of a safety factor tbh. Higher compression will help...
Jun 8, 2025
Frankieflowers
replied to the thread
4EFE vs 4EFTE engine block differences for forged engine build.
.
@daniel_g
May 10, 2025
Frankieflowers
replied to the thread
4EFE vs 4EFTE engine block differences for forged engine build.
.
Guys. Anyone can confirm that the FR vs FTE engine block side where the oil pump fits is the same? Is it only a matter of fitting the...
May 10, 2025
Frankieflowers
reacted to
gorganl2000's post
in the thread
4EFE vs 4EFTE engine block differences for forged engine build.
with
Like
.
yeah, i observed that same thing you and Jay mentioned during a past build.
May 10, 2025
Frankieflowers
replied to the thread
Hybrid turbo ct9??
.
Hello. Which Garrett are you (were you) talking about? Thank you.
Apr 16, 2025
Home
Members
Top