4efe head on 3e block

[gts limited]

Long story short
I had a 4efe head then got a 3e carb long block. Ditch the carb head and bolt on 4efe head and gearbox.

Will it run i know the compression gonna be low i will upload a pic in a few

4efe head
4efe intake
5efe pulley
4efte starter
4efe c40 gearbox
5afe throttle body
5efe distributor
4efte turbo manifold i going to boost it so its not laggy since the compression low
3e head gasket
5efhe injectors

more mods to come when it meets a shell

 

[Skalabala]

Cool! I love it when people do things like this
Some inspiration http://www.toyotagtturbo.com/forums/showthread.php?89967-2E-FE-build&highlight=4efe
What pistons are you using? Why do you say compression will be low?

 

[gts limited]

because the stock 3e pistons have a dish

 

[Skalabala]

Put 5efe low comp pistons
http://www.ebay.com/itm/Toyota-Tercel-Paseo-1-5L-DOHC-NPR-Pistons-w-Rings-5EFE-/300500929577?pt=Motors_Car_Truck_Parts_Accessories&hash=item45f7404c29&vxp=mtr#ht_4013wt_952
Shave the piston crown to drop the CR. Shave it so that it has a compression height of 29.5mm
Is the head on? How is the piston to valve clearance?

 

[gts limited]

Put 5efe low comp pistons
http://www.ebay.com/itm/Toyota-Tercel-Paseo-1-5L-DOHC-NPR-Pistons-w-Rings-5EFE-/300500929577?pt=Motors_Car_Truck_Parts_Accessories&hash=item45f7404c29&vxp=mtr#ht_4013wt_952
Shave the piston crown to drop the CR. Shave it so that it has a compression height of 29.5mm
Is the head on? How is the piston to valve clearance?

yes the head is already on i turned it over with the starter couple times already. I just need the ecu to fire the distributor and it might run

 

[gts limited]

Specs was a 3e carb block 12v sohc
MODS

5efe head 16v
5efe distributor
5afe ecu
3c-e map sensor
3sfe Tps
5afe 02 sensor
5afe knock sensor
5afe throttle body
c40 gearbox 4.058 corolla van gearbox final drive
5efhe injectors
bosch fuel pump
3c-e diesel water temp sensor
Aisin clutch
B18c plug wire
4efte wireloom
Denso ik16 plugs
5e timing belt
Other projects
ADD 1.8 8v volkwagen sohc
D15b 1.5 with ZC head sohc
3sge a140e trans
Runs good on ground

I use the honda and vw sensors to trick the ecu that its cold so it runs a bit rich but easy to start up because the ecu automatically advance the timing

without exhaust just 4efte manifold
http://www.youtube.com/watch?v=UeZOhOQcfJI

with a short piece of exhaust pipe with a shim inside to prevent excess noise where it is
http://www.youtube.com/watch?v=8sN6U0LhUSU

http://www.facebook.com/pages/Mundo-4afe-Tuning/100140550072644

was in this car but i took it out

Will try to run this vw on the toyota electronics lol

Future mods
a shell
axles
shifter
td04 turbo

 

[gts limited]

people say compression will be low but somehow the engine is very easy to run/start even better than some modern good cars just one touch of the starter wire and it runs

 

[gts limited]

getting code 51 i cant get rid of it but when i try to adjust tps code 41 and 51 come

 

[gts limited]

present mods



Uploaded with ImageShack.us

 

[Skalabala]

Are you mixing VW and Toyota now?? Some Toyota fans will have your head for that!
If I were you I wont use standard management!

 

[gts limited]

whats the best management

today i will try to get the alternator wired and working i do all wiring myself

 

[Skalabala]

You will need to ask around in your area to find out what the tuners there prefer.

 

[gts limited]

http://www.youtube.com/watch?v=6PIOf8zjQF0&list=UUPezIC9mKvUSEvEOgRwNKmw

I tried to redline the engine for the first time it seems the fuel mapping incorrect because at 4000rpm to 6000 it black smokes alot like an old diesel. The amount of smoke i saw if turbo was on the engine that would be some serious hp lol. I also installed a 5afe pressure plate and pour some oil in the gearbox