Emanage Software Drivers

Djaniero

Member +
I tried 2.30 first. I still get the error message but pressed ok then got through to the following screens.
On the bottom right, the software still says OFFLINE. Does this mean its still not connecting?
 

Attachments

  • IMG_20210120_175344.jpg
    IMG_20210120_175344.jpg
    102.9 KB · Views: 4
  • IMG_20210120_175102.jpg
    IMG_20210120_175102.jpg
    128.2 KB · Views: 4
  • IMG_20210120_175047.jpg
    IMG_20210120_175047.jpg
    132 KB · Views: 4
  • IMG_20210120_175037.jpg
    IMG_20210120_175037.jpg
    144.5 KB · Views: 3

Djaniero

Member +
Ah ok. I selected the 4efte engine code. Do I need to change the injector size to 295cc also.
I am guessing its working as when I hit apply it was asking me whether I wanted to save the file or export it to the greddy ecu?
 

Attachments

  • IMG_20210120_185347.jpg
    IMG_20210120_185347.jpg
    110.8 KB · Views: 4
  • IMG_20210120_190136.jpg
    IMG_20210120_190136.jpg
    167.3 KB · Views: 3
  • IMG_20210120_185432.jpg
    IMG_20210120_185432.jpg
    72.6 KB · Views: 4
again, i'm no expert here...as i dislike tuning and don't do it myself
however, from memory, when the laptop and the emu are hooked up and communicating via the cable, it will be making those changes in real time on the emu unit itself
 

take a quick look at this video for the initial cable and emu connection and messages
i get similar messages on my laptop when initially connecting and i think ONLINE as well in the bottom corner

somehow i get the feeling your laptop and emu are not communicating
do you have a different usb/printer cable you can try?
 
Last edited:

Djaniero

Member +
I'm the same. I know basics and enjoy the learning aspect of things, but for actual tuning, I leave to the pros.

Yes I have tried 2 cables so far.
I assume they are communicating as, when I made changes and hit apply, it asked me if I wanted to save the file or export it to the emu :)
 
I'm the same. I know basics and enjoy the learning aspect of things, but for actual tuning, I leave to the pros.

Yes I have tried 2 cables so far.
I assume they are communicating as, when I made changes and hit apply, it asked me if I wanted to save the file or export it to the emu :)
unfortunately that does not mean they are communicating...that message can be seen offline
please check for the above metioned things "ONLINE" and communication msg on the initial link up---as seen in the video
 

Djaniero

Member +
You were absolutely right.
I connected it to the car earlier and as you said it was still appearing offline, and i couldn't export the changes to the ecu.

Apologies for the horizontal view.


A friend of mine has a windows XP laptop, so I will try it with that next.

I wanted to try the earlier versions of the software also, but I wasn't able to download them in the link you shared above for some reason.
 
i don't know what is wrong , but i do know something is not quite right as you have a laptop/emu connection problem

some fo those links may be old. so you never know

but i figured the lastest version software from greddy's website should have work too-----it doesn't seem like a software issue as you have tried 2 versions now, but who know?!?!
 

Djaniero

Member +
i don't know what is wrong , but i do know something is not quite right as you have a laptop/emu connection problem

some fo those links may be old. so you never know

but i figured the lastest version software from greddy's website should have work too-----it doesn't seem like a software issue as you have tried 2 versions now, but who know?!?!
I will try the windows xp laptop in a ladt attempt. If that doesnt work I will be asking for a refund as I assume the unit isnt working.
 

Djaniero

Member +
Quick update.
I tried a windows 7 laptop earlier, install version 2.30 and it seems to communuicating now...software goes from offline to online when I turn the ignition on.
However I can't seem to figure out what parameters need to be reset to get the car to fire up?
 

Attachments

  • IMG_20210123_190551.jpg
    IMG_20210123_190551.jpg
    132.1 KB · Views: 4
  • IMG_20210123_190557.jpg
    IMG_20210123_190557.jpg
    167.7 KB · Views: 4
  • IMG_20210123_191300.jpg
    IMG_20210123_191300.jpg
    179.5 KB · Views: 4
  • IMG_20210123_191338.jpg
    IMG_20210123_191338.jpg
    221.1 KB · Views: 4
  • IMG_20210123_191347.jpg
    IMG_20210123_191347.jpg
    184.4 KB · Views: 4
  • IMG_20210123_191355.jpg
    IMG_20210123_191355.jpg
    122.3 KB · Views: 3
  • IMG_20210123_191409.jpg
    IMG_20210123_191409.jpg
    186.1 KB · Views: 3
  • IMG_20210123_191430.jpg
    IMG_20210123_191430.jpg
    191.8 KB · Views: 3
  • IMG_20210123_191439.jpg
    IMG_20210123_191439.jpg
    196.7 KB · Views: 3
  • IMG_20210123_191446.jpg
    IMG_20210123_191446.jpg
    180 KB · Views: 3
  • IMG_20210123_191455.jpg
    IMG_20210123_191455.jpg
    161.7 KB · Views: 4
  • IMG_20210123_191506.jpg
    IMG_20210123_191506.jpg
    109.1 KB · Views: 4

kylielucia63

Fresh Recruit
i'm not much into computers, but i use an old Dell laptop with windows XP 32 bit to connect to emu via the usb port. I bought it specifically for this purpose and to make my life easy.

a while back i tried using a newer laptop with windows 8 (if i remember correctly at that time) and creating a partition based on some advice (again i'm not IT minded),,,i installed windows XP on the partition and then installed the emanage software....everything seemed good, but whenever i tried to connect to the emanage unit i got issues with the usb driver...there was no communication between the laptop and the emanage. Someone posted a tread recently on how to possibly rectify this.
I’m having the same issue atm, did u ever figure it out?
 

Djaniero

Member +
I just used an old windows 7 laptop in the end, put all the tables back to 0 and the car fired up first time.
 

kylielucia63

Fresh Recruit
i'm not much into computers, but i use an old Dell laptop with windows XP 32 bit to connect to emu via the usb port. I bought it specifically for this purpose and to make my life easy.

a while back i tried using a newer laptop with windows 8 (if i remember correctly at that time) and creating a partition based on some advice (again i'm not IT minded),,,i installed windows XP on the partition and then installed the emanage software....everything seemed good, but whenever i tried to connect to the emanage unit i got issues with the usb driver...there was no communication between the laptop and the emanage. Someone posted a tread recently on how to possibly rectify this.
I couldn't get the new laptop/software to work with the emu.
i have to use my old laptop with Windows XP 32 bit installed
Yes I have the windows xp 32 bit laptop but there’s no connection when I hook up the emu to the laptop. There’s no driver
 
Yes I have the windows xp 32 bit laptop but there’s no connection when I hook up the emu to the laptop. There’s no driver

oh I think I know what you are referring to now. I had that issue as well when I first installed emu software on the laptop.
now i can't remember the exact process, but i fiddled around with the usb driver settings to activate it
Try via the original "Program" to "Trust" file to the usb driver OR the laptop USB settings (open the control panel, then click device manager, then click the usb driver you seek), but I clicked on something after being frustrated and it worked

its in the original manual, but unfortunately that specific part its in Japanese; however, I was still able to follow the diagrams to try to match what the manual was indicating. it'll try to find it in my manual later on when i get home.

unfortunately, IT and electronics are not my specialty, but hopefully something above helps to solve your issue
 
Last edited:
  • Like
Reactions: Jay
Top