Search results

For sale: Toyota bB 1.3 based on Yaris 2000 X Item Condition: Excellent bodywork, polishes up very well with very little marks. Really good lazy drive with standard comfortable interior, OEM mats Price and price conditions: £2,295 Extra Info: After two years of joyful ownership it's time to...

How doo guys. Could anyone listen to my engine from the YouTube link and tell me if they think it's serious or just a noise from it not running regularly for the past 2 years ( probably been started 5 times in 2 1/2 years) http://youtu.be/bcW0BXi8Ysg I remember the engine always being a...

For sale: Blitz Boost gauge 52mm Item Condition: Used Price and price conditions: £30 Extra Info: will come with wire and some hose (stand holder not included) Pictures: Contact Details: email me at impresiveg@hotmail.com Location: Preston, Lancashire Delivery & Conditions of Delivery...

For sale: Blitz DTT Turbo Timer Item Condition: Used Price and price conditions: £35 Extra Info: Comes with Starlet GT Blitz harness Pictures: Contact Details: email me on impresiveg@hotmail.com Location: Preston, Lancashire Delivery & Conditions of Delivery: Will post at...

For sale:Blitz Twin SBC Boost controller Item Condition: Used Price and price conditions: £95 Extra Info: Used and in good condition boost controller Pictures: Contact Details: email me at impresiveg@hotmail.com Location: Preston, Lancashire Delivery & Conditions of...

For sale: Toyota Sera GT Turbo Item Condition:Good Price and price conditions: £3,800 Extra Info: Starlet GT Conversion Contact Details: Via PM on here please Location: Lancashire/ Preston Delivery & Conditions of Delivery: Pick Up Year: 1990 Mileage: Car 260000KM...

I am after a driveshaft from the passenger side to either borrow (ahem) or to buy as cheap as possible in good condition to check whether my shaft is buggered or I need a new bearing. Will obviously pay for postage or pick up if close enough Ta very much

Yup, you have read right, I started the car drove about 5 metres then the engine stopped. Tried to start it to hear odd plastic banging noises then nothing. I suppose being so close to my house I was lucky. Pushed it back to my drive and left it as I was due to watch a movie at the flicks...

OK so my Sera Turbo has been off the road for a while having bits done but is nearly ready to be turned over for the first time. I have, however a plug left which has puzzled me to where I pulled it out from This is the plug It only reaches a small distance and comes from the lower...

After I got my head back from being skimmed I got these in the box of bits took off. Any ideas where they go? Ta in advance

Quick question. When using new head bolts to put the head back on do you need to lubricate/lube the bolts before they are torqued up? Ta

Has anyone got the plug that fits to the thermostat housing/cover and a length of wire that I can solder onto the loom as I have snapped mine at the sensor? Ta in advance Gav

When changing a head gasket I have heard from a Honda owner that you would need to change head bolts once they have been romoved as they stretch. Is this correct with the FTE engine? Figured I would just have to remove head, clean up, check stuff, put head back on using old bolts.... You...

Could anyone give me the part number for the pvc valve and seal kit, just broken mine and toyota will want a frame and chassis number from me, with having a sera i can't give them that :) Cheers in advance

I have a modified outlet from my CT9 to my FMIC pipes but the angle is too steep to fit my HKS actuator, does anyone have a aftermarket or modified (that enable the uprated actuator to fit) laying around that they don't need? Cheers Gav

Hey Dave, do you sell fuel rail adaptors seperately from the kits you do? If so can you give me a price? Cheers bud Gav

I wonder if anyone can tell me how to test whether the selenoid on my BLITZ Twin-SBC is working or not? Here are the simptoms: Controller lights up and can change from low knob to High knob but neither seem to make much difference to the boost pressure. Since putting on the controller the...

Have just aquired a Blitz Dual Boost Controller and was planning to plumb it in very soon. Still have standard actuator and was wondering if this is OK to do? Will only be running a small increase in boost for short amounts of time. (around 0.8 bar at the most) Im running standard engine...

love them and they are soooooo lighter compaired to my old 17" ones nice one dave!!!!

Should look like.... and shouldn't..... this is what the CT9 that blew up last Sunday now looks like...oh joy Good job I have a spare :) Most likely to have it all built back together by JAE...Hopefully