Search results

hey all, i have just fitted my new levin brakes and discs to my starlet. the pedal feels a bit soft and has a less aggressive bite. i bled the brakes and it all looked fine but thats the only thing i can assume is wrong. most of the parts are new. does anyone else have any ideas? i figure...

Is it likely or possible to be the inner CV joints?

did replacing the inner cv get rid of the noise then?

Hey all, I have a 5efhte ep82 starlet with an lsd and a few other goodies. My car has started making knocking & banging noises on corners, particularly at low speed and under load. There doesnt appear to be any issues in a straight line. My assumption was that it was the outside cv's and...

Hey all, i have a 5efthe starlet running Greddy Emanage blue and all the usual bits n pieces. It has been running fine for a while without issues but it has recently started to intermittently dive in rpm when at idle or coasting at low load. No issues noted up high. Any ideas anyone?

do you need to machine the disc at all (diameter or face?)

is there any issue offsetting the front wheels? do you have to get a new alignment, any other issues?

hey gang, i have a 5efte ep82 and have located some supercharged levin brakes and discs that im looking to buy. I know this has been discussed but I am still unclear on exactly what is required to change to this setup. Can someone please answer my questions below: 1) Do the levin calipers...

Hey all, im after a cheap upgrade to my brakes. I have read that the AE111 Levin twin piston caliper & rotors bolt up to the starlet front, is this correct? and are any modifications needed? Does it put the braking out of proportion having better brakes on the front? Secondly, what are the...

Hey all, I am installing a TD04L on my 5efte starlet and will be using the standard (TD04L) internal wastegate actuator. Can someone please post some pics of an installed setup with this arrangement, I need to work out what modifications are required to get the internal actuator to work. Thanks

Hi, im running a turboed 5efhe (low compression 4e pistons) with emanage blue setup, standard exhaust and turbo. ive been told i need to upgrade my turbo and exhaust as boost is currently limited to < 10psi, which is limiting performance. Im wanting to get 15psi and use car as daily driver. I...

Hey all im in NZ and need to upgrade my injectors. I have a 5efte and emanage blue (which is soon to be tuned). I currently have 315cc injectors but think they will be too restrictive so was looking for more like 370 - 440cc range. Im aiming for 250hp (or whatever I can get). Can anyone...

thanks, this is useful

looking for some good sized injectors for my 5efte running emanage. have seen the post with toyota and mazda injectors but how about mitsubishi injectors?

Hey all, I have just wired in my Emanage blue on my EP82. Just wondering where you guys installed the ECU on the car, doesnt appear to be alot of space behind dash. I want the install to look good and be out of the way. Photos or links would be good. Cheers

EManage Queries part 3 Hi all, hopefully approaching the end of my annoying questions. This one is regarding the ignition harness. I have read that only channel 1 is used as the starlets use distributors, is this correct? Which ecu wire do we cut into on a ep82? 't' is referenced in the...

Hey I think the above might be wrong. I understand channel 1 (blue / red) & 3 (yellow / red) emanage go to injector pulse # 1 & 3 and channel 2 (orange / red) & 4 (purple / red) emanage go to injector pulse # 2 & 4 Can someone please confirm what is correct? I will be doing this shortly

cheers mate, thats a start

EManage Queries part 2 Hey brought an Emanage blue have a few minor q's: 1) How do you know how to set the AIR FLOW ADJUSTMENT VOLUME switches, is this done using a a/f meter? or does the unit tell you when its set? or is it adjusted on feel? do you just raise the revs and adjust each...

Hey Wallace, I am about to buy a emanage blue for my ep82 5efthe starlet. Unfortunately the diagrams are not showing on your post regarding the installation, is there a way I can view these? Secondly, how did you know what the rotary switch settings should be (I can not find how they should be...