Removing bits around engine....Pic's inside...

sanchez

sanchez

Member +
Cheers mate, only just seen this, top job dude, repped :)

Stulet-GTT said:
Some pic's for ya sanchez...

First pic..
DSCF0614.jpg


This what i done with pipe...
DSCF0621.jpg


Dunno what the little black box is but it save fume's jus venting out into bay..

Then this little lot..
DSCF0617.jpg


Now look's like this...
DSCF0622.jpg


And these pipe's...
DSCF0616.jpg


Now like this...
DSCF0623.jpg


Wanna see if i can pull them out then plug hole properly with little bolt, the pipe with screw in end is just tempry...

Overall look ATM...
DSCF0620.jpg


Will look better once all cleaned..
Click to expand...
 
Stulet-GTT

Stulet-GTT

Member +
Im glad this has helped out a few of you to remove your's an tidy up ya bay's...

Think the battery moving will come later date for me but it is an idea i like...
 
danb87

danb87

South East England Area Rep
durmz said:
just get some beastly big gauge stereo cable mate
Click to expand...

right ill get some of that, is it best too run the cable through the interior? or undernearth the car as ive seen that done before on a mates car.

any idea how much i will need?

cheers
 
Last edited:
M

Motor

Member +
danb87 said:
right ill get some of that, is it best too run the cable through the interior? or undernearth the car as ive seen that done before on a mates car.

any idea how much i will need?

cheers
Click to expand...

Best to run it through the car mate; don't want it to short on the car if a stone tears the cable sleeve. Should fit under the door sils and then up through the rear trim; then there is a small bung on the driver side in the boot which you can pass the cable through.
Should be simple; just remember to get a sealed battery box (only thing stopping me doing it at the minute)
 
Stulet-GTT

Stulet-GTT

Member +
Foggy said:
Can this be done on a ep91? If so is it the same as the ep82?
Click to expand...

Yep i would say there pretty much the same, if you have a friend with a GT take a look at his while you do your's...


As for the battery in boot, i think i would take the seat's out to run power cable under carpet then i would insulate it in somink like sound deadnin stuff to stop in interfering with any think else...
Like running power cable for amp, you keep it away from other wire's for interference...
 
danb87

danb87

South East England Area Rep
ive been told not too use beasty wspeaker wire, as it doesn take the ampage aswell an can fuck the starter motor, so im on the look out for some propper car battery stuff.

my cars stripped out completely so the runnin of the wire is fine, how do you go about fixing the "battery box" down, does it need too be welded?

cheers
 
danb87

danb87

South East England Area Rep
what do people hold the battery in with? an links too a battery box, an cable at a good price?

any info on the fitting off it. welt? bolt down?

cheers
 
toyobaz

toyobaz

Member +
danb87 said:
ive been told not too use beasty wspeaker wire, as it doesn take the ampage aswell an can fuck the starter motor, so im on the look out for some propper car battery stuff.

my cars stripped out completely so the runnin of the wire is fine, how do you go about fixing the "battery box" down, does it need too be welded?

cheers
Click to expand...

try and find some welding cable 35mm should be good for 250amps
£3-4 per metre
good electrical wholesaler, welding supplier, or ebay
use proper crimp on or solder on lugs
 
sanchez

sanchez

Member +
the 2 metal pole things are th reused ones from the front, you could probs use the top clamp to mate, i couldnt on mine as its a bigger battery :)
 
danb87

danb87

South East England Area Rep
sanchez said:
the 2 metal pole things are th reused ones from the front, you could probs use the top clamp to mate, i couldnt on mine as its a bigger battery :)
Click to expand...

did you use the battery crate aswell or just clamp via the top bit dude?
 
Jaf_ep91

Jaf_ep91

Member +
on my glanza v i dont have that smal box you linked the pipe from the carbon canister to, has any1 got any ideas where i should loop mine to or should i not bother removing canister?
 
You must log in or register to reply here.
Top