some plugs that dont go anywhere? or do they?

B

BFannon

Member +
on the spade connection there is only one wire! i assumed it was an earth! but when i earthed it down to the tmic frame work the gauge stayed and its maximum!

Bill.
 
corofin12345

corofin12345

Member +
so your new sensor has a single spade connection ya and if so cut off the plug on the loom and put on a spade connection to suite sensor
 
B

BFannon

Member +
no right i used to have a 98 spec thermostat housing with a single three pin plug for the coolant temperature sensor. but because i am now using a 95 wiring loom i have purchased the 95 spec sensor which has only two pins on it and i have also installed the 95 thermostat housing which in the pics above has an extra threaded hole in it! which i assumed would be for another smaller sensor which would have a connection on for the spade connector? it is the smaller sensor that i am missing and need! the sensor that attatches to the spade connector on the wiring loom! ill see if i can make some sense with pics 2 mins!
 
B

BFannon

Member +
ha ha gotta love paint!

right the new thermostat housing is what is installed on my car now!
ABC.jpg

Hole A is what i am missing!

Hole B has a green two pin sensor screwed in it which has a green two pin plug attacthed to it!

Hole C is blocked off by a big bolt!

and these two are the plugs that i need to connect the green two pin attached to B and i would assume something needs to screw into hole A that would have a spade attached to it for the spade connection!
DSCF3003.jpg


does this help lol!

thanks

Bill.
 
B

BFannon

Member +
sorry if my post wasnt clear but i have blocked it off with a big bolt that was on my old thermostat housing but i need to know what should go in hole A can i have a part number or a picture of what it looks like!

Bill.
 
corofin12345

corofin12345

Member +
now weir on the one road mate

C = null and void.. nothing goes there.. use bolt from old housing to block it off
B = coolant temp sensor
A = temp gauge sensor.. all i know about this is when you plug it out the temp gauge rises to max..

ive searched and seached for the parts number you need and i just cant find it mate.. it doesnt appear to be on toyodiy either on any model unless im missing something.. may i suggest you also put up a thread with the picture you have there of new housing asking for that sensor (A)... ill keep looking for ya mate.. it may be 91611-60835 but it doesnt state what it is and is only down as a standard part.. have a look at link below

http://www.toyodiy.com/parts/p_J_1995_TOYOTA_STARLET_EP82-AGMQY_1603.html
 
B

BFannon

Member +
maybe this is what is missing then! i looked a link aswell but cant make head nor tail of it lol!
lol this serious stressing here!

Bill.
 
B

BFannon

Member +
you two are top dogs! will give toyota a ring tomorrow see what they say! do you think they will reconice that part number?

many thanks

Bill.
 
corofin12345

corofin12345

Member +
give it a go anyway man.. make sure you tell them that the housing you have has 2 connectors and your looking for the small "spade" connector sensor..
 
B

BFannon

Member +
you my man are a absolute diamond! if it is correct i will send you a drink!

p.s. i have repped you both for the info!

many thanks

Bill.
 
B

BFannon

Member +
well fingers crossed it will be

and where did you get them diagrams mate? they would be awsome to have them on my laptop or is there a manual i can buy for not to many pennies?

thanks again dudes beer.gif

Bill.
 
corofin12345

corofin12345

Member +
it was in that link i posted above mate.. it takes awhile to get used of it but once you crack it every nut and bolt on the car is in there... brilliant site
 
B

BFannon

Member +
but i cant veiw any diagrams where abouts are the drawings?

Bill.

i know site is great but didnt know were the drawings were i was going by the name of it! then getting part number from that!

Bill.
 
You must log in or register to reply here.
Top