Search results

Hi can somebody tell if the OEM LSD diff from MR-2 fits in a Glanza gearbox? think its also an C-family gearbox. would such LSD stand Glanza with 180PS-190PS ?

I also search some weeks before. Nothing found. Only ebay.

learn to control it will be long way, i thougt technical help would be better. I use greddy emu, possibly i can use an seperate output for an relay for boost control. I plan using an simple magnet solenoid. If its closed, bypass is closed and i got full boost. If solenoid is active, its open...

Hi, i build a 4efe Turbo. now i have problem with to much boost at 1/4 mile starting. To much wheelspin. So i think about OEM boost solenoid. this my car doesnt have but i use EP82 turbo ECU. so i have the PIN from ECU to be able to use such solenoid. I think about using normal Solenoid with...

hi, i want to buy exedy stage 2 3 paddle clutch for my starlet 4efte. Found some kits what fitte to 4age? this got same partnumber like the starlet turbo kit? are these same? Im some shops is only starlet listet , other is only 4age listed. i think should be TK02T441 ? is this correct?

interested in Greddy map sensor, but think its sold? (old thread) if still available, whats shipping to germany

@gorganl2000 this was the answer i want to know. thx

Hi, i want use ct9 Hybrid. THink this runs up to 1,2bar. So OEM MAP sensor would be good? The EMU ready the Boost with OEM MAP sensor, and send lower boost information to the OEM ECU to erase fuel cut? So i dont need the greddy Sensor?

Hi, iam planig install an Greddy EMU. Have already Greddy Loom, A/F gauge with output chanal for EMU I want to erase Fuelcut to run higher Boost with needed injection and ignition adjusting. WILL I NEED SEPERAT GREDDY BOOST SENSOR? Is OEM MAP sensor always needed?

oh, cool. these look very professionel. with gasket and made out of PC. I`ll watch these topic what happens. but its startet 2011, now its 2013 and nothing finished. I want these sommer such cover

this is one of the early covers. not bolted and not correct cutted

i post an picture of my tryed cover. Company produced will be better i belive

Hi, Iam from germany and search for clear cam cover but nothingto found. so i tryed to make one self. Used PMMA but got problems with the Tempratur. Always little Bubbles in the Plastic. So i searched an little company which can make these covers. I got an figure to make an copy in clear. They...

Hi, got my 4efte rebuild with Wössner pistons and Scat rods and ACL bearing. Can anyone tell what oil is original equipped in 4efte engines? what is proposed from Toyota? I heard after rebuild, an engine should run first 1000km with mineralic oil, whats with semi synthetic? should i use pure...

I search all these,without the black box shiping to germany possilbe? for what is these little black box needed?

hi, i search the OEM Efi pipe WITH she sticker plate "16Valve EFI" (from air cleaner to turbo). shipping to germany needed. OEM BOV is not needed hope someone can help

thanks jay,anything new? or can someone else help

no problem. here is an picture i watched at other engines from later toyotas, but couldnt find such plug

hi, i search the plastic connector for an OEM 4efte knock sensor. my plug is broken. Will need the plastic hosing and the PIN with little wire. Hope someone can cut out from an old engine loom? or what also will help is an Partnumber. I used toyoDIY.com but i couldnt fint connectors thx,Jan

so 0.6mm trd gasket is good thing with dished pistons to reach little higher CR for small turbos. And there are no problems known. this gives me a little certainty i will not kill my engine