Search results

Hi everyone , i've been looking at this car for some time now , the 4wd Fj cruiser , i didnt really like the interior , what do you all think about this car ? Have you driven it before ? cheers

heya everyone , after taking out the harness + field for inspection , i put it back in place without changing any of the wiring , however the the emu wont power up when ignition is on , all jumpers in place , all wires connected , dash lights come on , where might the problem be ?

hey everyone , soon after the dash was refitted besides the throttle pedal , car started behaving weird , idling very low , dies alone , or idles low and dies as soon as i touch the pedal , i found that the electrician has bent one of the stock ecu hooks so that it peeled one of the field...

heya everyone , ive been running the innovate lc-1 for some time now , only calibrated it before use , didnt do it again as recomended , its been working fine though , i know ive been running real rich , i think the sensor needs cleaning or something ? all wiring and s/w are correct , afr...

heya everyone , ive recently got an egt gauge , its sitting right under the ashtray , got about a meter or so of probe length , where should i put it , right underneath the gear selector or further down ?

heya everyone , i got a new gt28 , only done 200miles at mosr , installed on a forged engine , it had that usual sucking whistle sound , then it suddenly developed a supercharger whine abruptly , and got laggier in the process aswell , its got a filter on , and all piping was clean , when...

Happy eid everyone , no more fasting down here heh , Enjoy ! :D

heya everyone , ive recently finished a rebuild n the engines back in , the oil warning light however wont come on , and im very reluctant to drive it / run it in , the wire is connected to the switch on the front of the block on place , the bulb in the dash is working , earthing the wire...

heya everyone , got myself one these , 3 of 4 wires are pretty much straight forward , 4th wire tach signal , as per manual , says tap into the vehicle tach signal , which should i use , the source from the dizzy , and if so , where is it lol ! ty

heya everyone , ive been thru numerous other threads and i have compiled a list of culprits to check as follows : 1- theres fuel in the rail and injectors working 2- theres spark from the king lead and individual leads 3- dizzy rotor leads all in good shape 4- alternator / starter / all...

Not your usual 15 tonne Bmx :P http://www.youtube.com/watch?v=ZW5OB9vgoV4

hey everyone , ive seen from previous posts that the throttle body has 4 connections , 2 for coolant and 2 vacuum , that i understand go to the powersteering , ive found that 1 is connected , and one is closed off.. My power steering assembly is stock on this 91 1.3 carb 2e corolla , is...

hey everyone , i was previously using a helix clutch that i got from a member , plus pressure plate n flywheel , which i remember was lightened , apparantnly its a 5e assembly , used ony my 4e without troubles for a few yrs , however the clutch died and i got a new kit which i think is a...

hey everyone , going off from another aero thread concerning splitters , spoilers...etc ive been thinking about fabricating a light aluminum sheet to seal the cars underside and make airflow smooth , reducing lift/drag , any suggestions ?

lol just came across this , labour costs are phenomenal , parts arent as expensive as i imagined but yeh ! :)

heya guys , just found out something i find funny and catastrophic at the same time ! the previous engine builder , left me running with no thermostat for almost 2 years now !! the weird part is the car never really overheated , only sounds of some bubbles randomly after thrashing , this new...

hey ppl , i need the 4efte oil pump o-ring , and that oil pickup seal on the 3rd leg , as indicated in the diagram , ty

hey everyone , im in need of a toyota oil pump o-ring seal , which other models fit , besides the 5e one ?

heya everyone , couldnt find a real solid answer , what would be the maximum boost a garrett gt2560 can take , and the usable psi on a built 4e , couldnt really make it out from the graph but look like 1.5bar ?

heya everyone , im in the process of installing new forged pistons / rings / big bearings and rods , and we have no balancing here at all , no machinist or pro does it , would it be okay to weight each assembly individually and install them as is ?