Search results

Hey guys,i've had a walbro fuel pump and a sard fuel pressure regulator in my car for a while now and it worked perfect.Recently i observed that wen the car goes under boost ,the fuel pressure drops .Then one day the pump sounded real loud in the tank.I then removed it and put in a new walbro...

Hey guys ,last year i broke my third gear ,got another set of gears ,placed them in my case and broke the same third gear again. I got me another gear box and i opned it just to put in my TRD LSD.Wedneday morning i was out driving a bit hard but not hammering any gears when the third gear broke...

Hey guys go me a bit of a problem here.If i have my car for a while and it gets to operating temperature and i turn it off,when i restart the engine i sometime idle real shitty and my afr on my wideband reads 17 and sometime flat out .when i drive about a bit it den idles fine .So tonite i...

Hey guys, where can i find a set of indiglo dials for my Mark1 turbo starlet if any?

Hi guys, i'm after a 6 point roll cage for my 92 ep82 starlet , so if any of you guys know of any ,link me as i think i need this right about now.:rockon:

WANTED: Left and Right quadlamps and Grille please:rolleyes:

@weeks after building my 5efthe,my crank went and so i got me a new one and replaced it .After i put the engine back in i begun smoking .While idling it would be letting of a light smoke but when i accelarate it ,a cloud of smoke would come out the exhaust.I changed the valve seals about 3 weeks...

Hey guys ,i'm gonna open up my engine :(,and i was wondering if i can reuse my Speedvision metal headgasket and my ARP headbolts:confused:

I just recently built me a 5EFTHE ,and it was working fine until i spinned a bearing and messed up the crank.I put in a brand new crank from toyota and when i put the engine back in ,i am letting off alot of white smoke. Inspected the turbo which was brand new with the build and it is fine.Alos...

Hey guys,just built me a 5EFTHE and it had been working fine for about 2 months.All of a sudden i am smoking out the exhaust .I pulled out the spark plugs and took my flashlight and lite down in the cylinders ,only to find that all the top of the pistons are wet,i did a compression test and it...

Hi guys, can anyone of u give me the jumper settings for the EMU please:confused:

Hey Guys , i've been having this problem where my engine was giving trouble to turn over ,kinda like a hydro lock .I retarded the ignition timing on the EMU to -9 (1000rpm and before) where the map trace is on idle and all berfore idle and now she starts fine Why :confused: If i zero the...

Are anny of you guys using this pressure plate? If yes, have you encounter any problems with it in terms of it damaging thrust washers?

Hey guys ,in the parameter setting section ,and go to the vehicle set up ,if you dont put in the right figures for the off set angle ,will this affect the timing and cause a hard start:confused: secondly,when running a 5e set up ,what do you set the engine as there isn't any for the 5e .and...

Hey Fellas ,sometimes i would turn my key and the car will start in one go .Another time she will turn over alot and when it do start ,you can hear the sound of an engine that has been flooded and puffs out some black smoke .At times it is so bad ,the engine turns over like is hydro locking...

Hey guys,if i am fitting a new crank form Toyota ,how do i know what mark bearings should i use? or how do i calculate what size i should use?

Are any of you guys using these pumps If yes ,what are you all reviews on this?:beer:

Hey guys i just built a 5EFTHE and is spinned a bearing and dismantled the thrust washers .I open a threah a few day ago about me trying to figure why when i press my clutch ,my rpm drops alot.It turned out to be that the crankshaft was walkin:mad:Can someone explain to me why my thrust washers...

Can someone tell me what is the difference in terms of the crankshaft and bearings between these two type of engines? as they seem to carry different part numbers for the crank and bearings but might be the same

Hey Guys, i have recently forged a 5efhe i got form japan with only 64,000km on the dial.I stripped it down to the bone and rebuilt it from scratch .I replaced everything new .I used acl bearings and an ACT extreme clutch kit.The problem is ,when ever i press the clutch pedal ,my idle drops...