Search results

Hi all, I have a few parts that I want to shift. I am open to reasonable offers on all of them. The parts are located in Waterford, Ireland but I am located in Cardiff, UK so my parents will be looking after the sale of parts. I am driving from Waterford to Cardiff in late January so I can...

Hi all, I am looking for another project car. I am looking for a mint shell and thats it! If it has an engine its a bonus! The car must be in Ireland for ease of getting it! Thanks, Alan

Can anyone tell me what type of exhaust is the front and middle section of this exhaust from? http://www.flickr.com/photos/44944971@N05/6692153197/ The back box section does not match it and that is an apexi. I thought it was an apexi but it doesnt match. I think it might be a blitz...

Hey all, I am looking for an alternator for a glanza asap. It must be in good working order and not damaged. I can collect it within the South East of Ireland otherwise the seller must be willing to ship it to Waterford, Ireland. Thanks, Al

I changed my clutch to a CAP clutch and put it all back together but I cant select gear. Before I go and open her up again I want to list the possible reasons. When you push down on the clutch the slave cylinder moves over so it looks like she is bleed correctly.

Folks, Does anyone have a Lamda sensor for sale? Alan

Hi folks, Can anyone recommend good julbilee clamp clips I can buy on ebay for the intercooler hoses? Thanks, Alan

Hi all, I have an autobahn intercooler as as most of you are aware the piping on this goes over the manifold as it passed to the turbo. This in turn is causing hot air to go into the turbo and I want to eliminate this by making the intercooler piping from the intercooler to the turbo go a...

Hi all, I want to change my handbrake cables but the heat covers underneath dont seem to have removable bolts. They just have rivets. Is it ok to remove these and leave them off? I dont see how I will be able to get them back on once they are off.

Can a clutch on a glanza be bleed the same way as is shown in the video? http://www.youtube.com/watch?v=wdf--suwqw0

I want to refurb my brakes. I want to strip the calipers down, give them a good clean and change all the seals. How big of a job is this? What tools are needs to change the seals? Does anyone have a diagram outlining the part numbers of the parts needed?

I am looking for the bolt that attaches to the CV drive. Basically that attaches to this: http://www.flickr.com/photos/44944971@N05/4695811105/ And I am also looking for the lower rad house. I replaced my housing from a 1996 glanza to a 1998 glanza and the location where the hose attaches to...

Hi all, I am looking for an alternator and starter for an ep91. Must be in working order. I can pick up around Ireland, otherwise the seller must be willing to post to Ireland. Thanks, Alan

Hey all, I have been away from here for a while. I am still working on the glanza. Here are some recent pics.

Hey all, I am having a problem starting my car. It basically is showing no signs of life at all. It is as if the battery is not connected at all. The battery is new as in 1 day old, and everything is connected like it should. I am thinking the problem is with the ignition, but where do I...

Is my RRFPR ok positioned like this?

Well what can I say, absolute nightmare is the word. They are so tight to install it took me a whole day to install all 3. I am talking about installing them into the car and not actually fitting thrm to the mount itself, although, that is a job in itself! I though they would give enough room...

This is a shocking story I came across today. I cant believe people are so narrow minded and stuck in ther past of Northern Ireland. http://news.bbc.co.uk/2/hi/uk_news/northern_ireland/8024732.stm It does not matter what side of the fence you are on, this is terrible to do to children. We are...

Hey all, I am currently looking for some JDM 15" alloys. I will be purchasing in the next 2 weeks. You must be able to ship them to Ireland too. Show me what you got!

Im looking for a set of second hand Enkei alloys. I am not sure of the make but where is the best place to get proper JDM wheels. I tried the usual places like Ebay etc. Can anyone recommend a place. I also tried the Jap auction, and they are overpriced due to the value of the yen. Cheers, Alan