Search results

  1. A

    96/98 glanza engine loom differences

    Hi I in need of a new engine loom for my 98 glanza do I have to buy a 98 1 or will a 96 loom work with a 98 ecu???
  2. A

    gt fan switch sensor

    i need a new fan switch sensor for my 1994 gt does anybody know if this will do the job? http://www.ebay.co.uk/itm/Temperature-Switch-Radiator-fan-for-TOYOTA-STARLET-YARIS-DAIHATSU-YRV-1-0-1-3-/281125167067?pt=LH_DefaultDomain_205&hash=item41745d9fdb
  3. A

    gt engine block

    as title says i need a block
  4. A

    arp head bolt torque setting

    i need to no the 3 stages to torque the head anyone know??????????
  5. A

    dd coilovers

    looking for a set of coilovers and saw these on ebay has anyone on here used these before, any opinions on them http://www.ebay.co.uk/itm/DD-40-Step-Coilover-Shock-Suspension-Toyota-Starlet-EP82-EP91-89-99-Free-Postage-/231164471563?pt=AU_Car_Parts_Accessories&hash=item35d279e90b
  6. A

    hub fitment

    Will a hub from a glanza fit a mk2 gt?????
  7. A

    clutch problems

    no the pressure plate is fine i mean that 2 of the springs came out the the clutch plate and all the rivets that hold it together were very loose too. havent taken the gearbox out yet to see what condition the new clutch is in but has the same symptoms has the previous time the clutch failed...
  8. A

    clutch problems

    hi is problem is that my friend got an lsd gearbox for his glanza about two weeks after he put it in the clutch failed which was work find for a year before he put the gearbox in. so he bought a new blueprint clutch and put it and its been about two weeks and now the clutch is gone again any ideas?
  9. A

    what make is this

    are you sure it is not this one? http://www.id-workz.co.uk/index.php?main_page=product_info&cPath=3_1118_1211_1228&products_id=628
  10. A

    exedy release bearing

    I need a new release bearing for my exedy paddle clutch i have a standard toyota bearing in atbthe minute but it makes a grinding noise until i push the clutch peddle down is there a heavy duty bearing i can get for it?
  11. A

    ignition timing out

    I just finish rebuilding my engine last week took it down to a local garage to get ignition timing set and its sitting at 30 degrees out so took it home and took timing cover and rocker cover off . the cams bottom crank pully and top marks on the head are all lining up what could be the problem???
  12. A

    forged engine first start up

    Cheers guys got her sorted pull efi fuse and king lead turn it over a couple of time until oil light went out and oil started flowing from turbo then put fuse and lead back in and fired her up. Does anyone no if there a guide for setting ignition timing cos i need mine do asap....cheers
  13. A

    forged engine first start up

    Can i just start the car up or do i need to turn in over first to get the oil round the engine first and any tips on how to do this ??????
  14. A

    cant pm you clear your inbox

    cant pm you clear your inbox
  15. A

    Crank pulley unbalance?

    when i took my pulley for the crank i chipped i bit of the inner side wall of the pully about 1/3 of the way around off .do you guys thinks that it is now unbalance? should i get a new one like this http://www.fensport.co.uk/Parts/Model_39/Category_1/2311 only asking cos my going to be...
  16. A

    38mm external wastegate

    Looking for a 38mm external wastegate . Anyone got 1??????????
  17. A

    Clutch

    Looking for a second hand clutch for my mate's gt .needs to be rated to 250bhp+
  18. A

    Lightweight flywheel

    As above looking for a light weight flywheel. any for sale ??????
  19. A

    Ignition coil

    yea its for a gt could i pick it up today
  20. A

    Ignition coil

    lookin for a ignition coil the thing that the king lead goes into and the 2 plugs on top of it. need 1 asap
Top