Search results

I am looking for a paseo gearbox

I have uk and glanza springs here. Both have the same diameter wire but the glanza has half a coil more spring. The question is which will be the stiffer spring and which will be the higher spring.

Ive a 4efe automatic for a winter runabout. Is the fte auto a fully mechanical box? It would be nice to have a backup option if the fe unit failed. Also can anyone chart these ratios as it doesnt work in the usual gear ratio calculators 1996 UKDM 4EFE Automatic (A132L) 1st : 2.810...

Recently bought a wee N/A for goin to work. Id like to get a whiteline rear arb and panhard rod as I sold mine a few years back to a guy in a Dungannon petrol station. I still have the castor bushes lying in the garage; these plus a oem strut brace should give me a few extra minutes in bed..

For sale: ACIS Inlet manifold- adapter and throttlebody to suit N/A included Item Condition: Perfect working order and complete,, no missing or damaged actuator Price and price conditions: £100 complete with all attachments - NI discount available Extra Info: Need this sold this week...

For sale: 5efe engine from a 99 paseo. Rebuilt with less than 1500 miles since rebuild. Was sellin the paseo so removed this first. Head rebuillt by Powermax, bores honed by powermax and acl bearing for rods n crank plus seals supplied by powermax. Its been stored in my garage for last two...

Its minus 13celius and your on your way to work. Your car heats up in 5minutes but still no heat from the incar blowers,, then,, suddenly the tempature hand rises to the top of the guage and you think DAMN. It then drops back to halfway. You stop immediately and let it cool down. Your...

Im scrapping all my junk and Im trying to remove valve guides from a few old heads. Are these pressed it? I cant see any clips or the likes so do I drive them out with a heavy hammer?

How much boost can a n/a clutch take in a GT? Young neighbour has broken his new clutch and Ive offered to stick in my spare n/a clutch. Im pulling him out of a hole for a few months and Im wondering what I should screw his boost down too. Its sitting a 0.9 at the minute with toby exhuast and...

Want a CT9 and downpipe in northern ireland

Lost my old key fob for my factory tvis alarm system on the paseo. Can anyone remember how to program in the new key fob, it has somethiong to do with the green button on the alarm ecu. Its a TVIS IIIB

Im bodging in a ep85 ecu to my now 1300 paseo using bits from the fte such as ignitor, dis and throttlebody, but just wondering if any 4x4 lads have the harneeses lying around. Please reply via PM

Ive got lists of gear rarios but never knew 100% which gearbox was in my car. Noticed this on a VIN plate earlier today. Although I still not sure if the code is written on the gearbox anywhere. VIN plate is on your bulkhead behind inlet manifold. Colourcode/TrimCode/?/Transmission. This one is...

Badly need a exhaust plug to fit a 4inch jap can, damn the cars loud an driving me mad. Needed asap

Need spacers prefer 10mm-20mm hubcentric 4x100 Not payin £200 for a new set

EP85 ecu into uk 4efe thread Ive changed plans and am going with a ep85 4x4 4efe ecu in my uk spec 4efe Im fitting a glanza S 100ps ecu to my uk4efe loom and cant indentify these few pinouts. CAN ANYONE HELP SEL NC CF 4E-FE GLANZA S ECU pinout Pin Name Wire color Explanation...

Im making a field extension harness today but I cant get the damned loom plug split so I can pull out the pins and wires. I found the wee push in piece on the bottom but cant get it pryed out to release the pins. Can anyone help

Really need wheel spacers, 10mm-20mm ish and prefer hubcentric if I can

Ive a neighbour lookin a block he bought all bits off ebay including a 4efte block sold as a 5efe, ripped off.

What size is the thread of the fuel line end that screws into fuel filter, no the banjo end. Is it 12mm metric or 1/4bsp or how will I figure it out. Im wanna fit a tee piece and a pressure guage on my 5e for throuble shooting purposes