Dump Valve King Thread - A discussion

[Sassu]

ssqv - makes a chirp sound
hks - pttssshh sound lol

OR!!! loose the resirc valve block the vacume and so on and get the all mighty

PIDGEON!!!!!!!!!!!!!!!!!!!!!

 

[Adam_Glanza]

lol sassu i think you mean

hks - chip sound

blitz - psssth sound

greddy - ching sound

 

[Sassu]

i dnt know why i said hks for the second lol i meant bov...

greddy one? that like a kids bicycle bell? god greddy goin down hill lol

 

[Adam_Glanza]

it sounds more like a glass breaking noise i think lol, i kinda like it tho!

listen to it on the tube its quite nice

 

[rb69]

The Greddy Type S sounds awesome if you can get hold of them.

 

[yan]

What abt power xs m8

 

[Rik]

You can also get a different insert for the ssqv for a deeper sound instead of high pitched

 

[Fishy89GT]

agree with Dub, Greddy Type RS is my fav aswell...or just not running one

 

[Duff]

Running without a BOV>

Kinda getting sick of my SSQV and been thinking of running no BOV, when people say this though do they actually take BOV clean off the car or just disconnect the vac hose going from the BOV to the inlet mani? Does it make a difference which way ya do it?

Thanks.

 

[Fishy89GT]

Kinda getting sick of my SSQV and been thinking of running no BOV, when people say this though do they actually take BOV clean off the car or just disconnect the vac hose going from the BOV to the inlet mani? Does it make a difference which way ya do it?

Thanks.

i take the bov totally off. and then just block that vac pipe....thats what everyone does basically.

 

[Duff]

Block the vac pipe with what? a cable tie or something? I'm thinking of just disconnecting the hose from the BOV and blocking it with a cable tie or something, would that do any damage?

 

[yan]

Same here just get off the ssqv lol. The air needs to re circulate even though i am running without bov

 

[Dane_Bristol]

Just screw a little bolt or screw into the vacumme line at the end job done.

 

[Duff]

Just screw a little bolt or screw into the vacumme line at the end job done.

So block the vac line with a screw, is tat what your sayin?

Thanks for the quick replies lads!

 

[Cooch]

Stick a bolt in the vac hose and cable tie it good! When i had mine i took the dump valve out completly and blocked the pipe. A lot of people say dont do it but the same amount of poeple have done it with no ill effect. As long as your not running huge amounts of boost you will be fine.

 

[Nwimie]

Just screw a little bolt or screw into the vacumme line at the end job done.

easist way! ^^

ive just screwed my BOV up tight so it gives some chatter + dumps at higher boost pressures :]

 

[Duff]

Stick a bolt in the vac hose and cable tie it good! When i had mine i took the dump valve out completly and blocked the pipe. A lot of people say dont do it but the same amount of poeple have done it with no ill effect. As long as your not running huge amounts of boost you will be fine.

Thank you kind sir! Rep for everyone!
:gt-smilie:

 

[Aidan@EP-styling]

when you take the bov off you need to block both pipes that went into the bov. the boost pipe coming from the intercooler needs to be completely blocked off (sealed so no air can escape) and the vacuum pipe from the inlet manifold needs to be blocked with a screw or something.,

 

[Dane_Bristol]

So block the vac line with a screw, is tat what your sayin?

Thanks for the quick replies lads!

Yeah depending on the size off the bolt and fitment just screwing in is sufficient enough. Its only a vacumme pipe you aint running huge boost through it.

 

[stuart]

I used 2 bolts blocked vacuum and IC up chattery woop :homer: