Search results

For sale: A TRD Helical LSD, part number 41301-AE000 Item Condition: Good (see picture) Price and price conditions: 450 USD (open to offers) Extra Info: Item was bought for my Mazda 121 4EFTE project, but sold it earlier this year, so no longer use for this item. Bought it used from...

For those of you who don't know or don't remember, i own a mazda 121 db with a 4efte on it, it's been a cool project so far but i just moved on to a new one... I recently purchase a Nissan Silvia S15! :), i bought it without an engine and with a few bruises here and there, but i've been working...

Hi everyone!, I've had an issue with my engine since the first time i turn it on, is not really an issue but i know something is not right, let me explain... When on idle the car hesitates a lot, but the revs doesn't move neither up or down, it varies a little bit but is almost imperceptible. I...

I finishied installing the TRD Helical LSD and CAP Clutch onto my car on the weekend, first time doing this kind of job, wasn't that bad at all :p. First impressions is that right now the clutch is juddering when coming out from a stop (is going to get better after the clutch bed in), also the...

Hi, i'm looking for the torque specs for the differential into the crown ring. I remember looking somewhere that it was 97 N.m, can anyone help me please???

Hi, i've been thinking for a while about this, right now i'm using a 2jz map sensor on my car and it's been working fine, no issues at all. My question is, this is a 1.2 bar map sensor, while the gt one is a 1 bar map sensor. I've heard that this is a common upgrade for people using 1jz supra to...

Hi, i'm going to replace the clutch myself, i read the tutorial here http://www.toyotagtturbo.com/forums/showthread.php?t=31642 in how to replace clutch. My question is, do i need special tools??, i'm going to install an lsd as well, i read somewhere here that installing a lsd is as easy as...

I opened this thread to give feedback on ab88 manifold after 1 year of use. I've been running this manifold for 1 year now, and it doesn't have any signs of cracking. The welds looks the same, running it at stock boost with a few mods done to the car (full exhaust, intake, downpipe), right now...

Just to inform you guys that the company i work for (Eaton) did a reduction of 8,600 employee worldwide!!!:(, (6 of those 8,600 were some friends of mine!!!):(... just sharing my sadness with you guys!, hoping this doesn't continue any further...

Hi, need some advice from you guys! Some guy here where i live is selling me a TRD Helical LSD and he's asking 590 USD for it or he can sell me one without bearings at 535 USD, is that too much??? i think it is cuz i remember seeing TRD Helical used around 450 or so. What do you guys think??

Hi guys!, i need to know the part number of the ignitor, that's the grey little box beside the coil. I need to know it for a Starlet GT pre 92 and for the 92-96 one. Thanks!!

hi guys, i just finish doing the wiring loom of my car, and now i'm getting fault code 12!!!:(, the car splutter a bit when accelerating from low rpm and when going full throttle it sounds like misfiring and it feels slow!!. What things could be happening?? also, does the ignitor runs hot on...

I need some help on this one, for the people that have worked on the wiring loom on 4efte swaps or on the starlet (ehem Sagittarius...:p). I wish to know when the idle air control valve is activated?? i tought it was when the ecu receives a 12v signal from ELS wire, but when i do that nothing...

Hi, I want to know if the slave and master clutch cylinder that the engine uses is the same as the 5efe paseo one??? i'm asking that because i can get those two from the paseo quite easily as i can't find the 4efte one. Thanks... Also, here's a link for the slave in ebay...

Hi, i'm trying to identify one of these sensors, can anyone help me??? This is what i know: 1 - Coolant Temp. to ecu 2 - I think this one is water temp. to dash. 3 - i don't know what is this for... Also this are the two connector for both 2 and 3, but don't know which one connect to...

Hi guys need some help here... I'm doing my entire engine loom again because of some electrical problems i've been having since i did the swap back then. I found out a lot of messy work that my mechanic did, but let's not get in to that subject.:p. The thing is that i've been following a...

Hi, i just bought an e manage and it came with all the harness (main, injector, ign.), the only thing that I'm missing is the 3 bar pressure sensor, but I've heard that i don't really need it because I'm not planning in running more than 1 bar of boost. Can someone clarify me on this??? Do i...

Hi to all TGTT members!!!! I've been reading and posting in this forum for some time now, but i haven't still introduce myself neither my ride. So here it goes! I'm from the Dominican Republic in the Caribbean and i own a Mazda 121 DB "Bubble" car with a 4efte engine in it. I've recently created...

I've been wondering if anyone here has done a distributor less conversion (direct fire ignition)??? i'm thinking of doing it after i have the emanage install on my car. What do you guys think, is it worth it???? what stuff i have to buy for this to work??? I've been having so much trouble with...

Quick question about the icv... i just realized that my icv isn't working because i removed the plug and my idle stays the same and does the same thing when i turn the lights on. I don't have power steering on my car, so my question is, is the icv only for power steering or is also for...