Search results

Replaced the whole of the loom in my 93 gt and rewired in the emu Now it seems to be overfueling, missfiring and as soon as it warms up (around 5minutes running) it just dies... it was running fine before putting the new loom in however ive changed spark plugs, coil pack and tried a new...

Purchased a forged engine of a seller and put it in..started the car and let it idle for 2 minuted, then turned it off and after 5minutes if poured out with coolant from the inlet manifold so took that off and what i could see different about this engines head is it had a hole drilled in it and...

I Need the whole front Lighting Looms including the fusebox in the engine bay with the fuses and all the way through to the ignition....NEED ASAP...CASH WAITING! Would Rather Collect as i need them desperatley, im located in bromley, kent but give me postage prices :y:

im after the full interior ignition loom thats covers the whole dash, NEED ASAP!

Right the other night my rear lights and dashboard lights went out, found out it was a 20amp fuse so changed that as i got home, then last night on motorway a shit load of smoke came from the steering wheel so pulled over and could see flames coming from the wiring, i paniced and smashed the...

everytime i get to around 46 posts it droped to 41 or as now drops to 24 :S anyone with any ideas?

Looking for a set of either 15" or 16" black alloys with tyres with good tread need to be 4x100 also willing to travel 1hr from Bromley / Kent or include courier prices... Let me know what you got ..pics too

they are 4x100 but Im quessing no due to the stud size of the hubs but need confirmation please :)

Only have cold air blowing, Replaced thermostat but no joy Just flushed through the heater matrix pipes but most of it just splashed back and only a small amount was running out of other pipe... Does this mean replacing the matrix? or is there another way around having to remove the...

having big issues starting it up on cold now..but starts up fine when warm Checked timing Changed spark plugs My turbo timer shows the battery voltage and it shows up at 8-9 when trying to start and 12v when on idle Please help :)

basically if i get home from work and start the car it will start alright, then turn it off and try again and it just cranks and cranks and cranks...take a couple of minutes to start and after that time theres a strong smell of petrol for a few seconds ? I had some standard spark plugs so put...

Right guys ive tried having a look at other threads but cant seem to find one to suit. replaced the Headgasket and that seems fine i.e. good compression, no contamination, no overheating etc.. but since this my fans only blow cold air...however before i cooked the headgasket It got warm but...

must not knock or make any sounds and be in good condition... No timewasters....

Needed a new engine so i think i may of brought a glanza engine for my gt...Done he headgasket but just curious now as to wether there different???

Basically i overheated the engine and cooked the headgasket, water was splurting from cylinder 3 when i done a compression test...however there appeared to be no water in the oil at this time, Took the head off (had it skimmed), Had a new headgasket kit so put everything back together and fresh...

Need the connector bit that connects on the top left of the inlet manifold.. 1 wire come off mine so need it to be just cut along the line and both wires still in there :) Picture: http://www.toyotagtturbo.com/wiki/icv1.jpg

In need of: distributor cap Magnacore king lead Coil pack ( the bit where the king lead end plugs into) Need these asap and got money ready to be sent.. Best to text me on 07500042822 Sam.

In need of a drivers side hub for GT ep82, all 4 studs with no damaged threads :)

Ep82 on bc coilovers.. Basically i remember up untill when we had the really bad snow I was doing around 45mph on moterway and slowed down as I spotted a few patches of black ice..so going around 33mph now and It still spun the car so I was facing the opposite way..I know its common to skid...

basically, from centre to 1st is bad Removing it from 1st is Very bad Into 2nd is bad Removing it from 2nd is bad into 3rd is fine Removing it from 3rd to 2nd is Very bad i sometimes literally have to snap it out. Ive checked gearbox levels and topped it up untill it was fine, it...