perreau
Member +
I have Win 7 ultimate x64 not working...so i have Win 7 ultimate x86 running in VMWare...works like a charm
The Official EMU Tuning & prob thread! Launch control success thanks to fur!
- Thread starter nyahbingi
- Start date
I have Win 7 ultimate x64 not working...so i have Win 7 ultimate x86 running in VMWare...works like a charm
jayc-glanza17
Fresh Recruit
dont u have to assign it to any of the jumper switches??
HYBRID
Super Moderator <a href="http://www.toyotagtturbo.
Guys,
if only you bother reading through all the knowledge of this thread, i can assure you that every single setting needed to setup the launch control on the ep91 and ep82 are available.
I think when i have some time ill adjust/prune and tidy up this thread..
iv gotten the launch control working on the both the glanza and gt... without the tps wire connected on either
kon
if only you bother reading through all the knowledge of this thread, i can assure you that every single setting needed to setup the launch control on the ep91 and ep82 are available.
I think when i have some time ill adjust/prune and tidy up this thread..
iv gotten the launch control working on the both the glanza and gt... without the tps wire connected on either
kon
HYBRID
Super Moderator <a href="http://www.toyotagtturbo.
Just finished cleaning this thread up, please try and keep it as technical as possible guys, iv removed over 300 posts of unrelated posts.
Ill update a few things about the emu in a couple of days as there is alot to add in this thread.
kon
Ill update a few things about the emu in a couple of days as there is alot to add in this thread.
kon
Sheldon
Malta Area Rep.
just a quick question.
why do i need an injector adapter #2 with my e-manage ver c when on the description of the dapter #2 it says
Ultimate INJ. Adapt. #2
Notes: prevents overly rich condition for 6 cylinder vehicles
Part #: 15901504
Price: 25.00
im sure i only got 4 cylinders
why do i need an injector adapter #2 with my e-manage ver c when on the description of the dapter #2 it says
Ultimate INJ. Adapt. #2
Notes: prevents overly rich condition for 6 cylinder vehicles
Part #: 15901504
Price: 25.00
im sure i only got 4 cylinders
perreau
Member +
I asked the same question as well, but i listened to my elders and it did solve my "running rich" problem
Sheldon
Malta Area Rep.
I asked the same question as well, but i listened to my elders and it did solve my "running rich" problem
hah! yeah well im gonna get it anyway... but i would like to know why just to learn more
thanks for your reply.. was it very bad without it?
ramses974
Member +
Sheldon take a look at your ultimate serial number & take a look at the manual wiring for Adapter n2. it is written
"This adapter is used for vehicles that get a very rich condition when wiring the
injector channels for +/-.
※This adapter is build into the e-manage Ultimate hardware from serial num. 4000 - on"
Sheldon
Malta Area Rep.
got my EMU at the garage.. il check tonight. where is the serial number located? my board is version C
Sheldon
Malta Area Rep.
btw. you got a link to the inj adapter #2 pdf file?? or can u send it via email?
EDIT: i found it - http://www.naikontuning.com/det_tec...04/e-manage-ultimate-injector-adaptor-1-3.pdf
so we only use 2 grren wires and a red wire on our ecu?
as we only use channel #1 and #2 right?
EDIT: i found it - http://www.naikontuning.com/det_tec...04/e-manage-ultimate-injector-adaptor-1-3.pdf
so we only use 2 grren wires and a red wire on our ecu?
as we only use channel #1 and #2 right?
Last edited:
ramses974
Member +
the serial number his behind the EMU no need to open it
Sheldon
Malta Area Rep.
well it was so,mething 03333? dunno.. anyway today picked the inj adapter #2 and received the EMU harnes.. off to the garage to install it
prepare for some more questions you emu gurus