Search results

hey up people im currently finishing building my 5e that im having loads of trouble with! my setup is...... 5e bottom end using 5e pistons etc, 5e head with 4e cams and 4e distributor running 1.9mm head gasket on td04l ........ running 4e timing compression is 130psi over all 4...

ok basically ive had a look but cant find a propper answer? im building a 5efte atm using the 4efte head and just using all the 5e bottom end, it already has the thicker fhe rods but im just wondering if ill be ok using the 5e pistons but with a 1.9 athena headgasket to lower the compression...

ok basically just started testeing my td04 turbo running standard ecu with sard fpr set at 2.5 bar now its running external wastegate and ive set it at 0.6 bar and it holds boost perfect with no creep but sometimes when accelerating hard the car cuts but it doesnt feel nothing like fuel cut its...

hey guys next question are the 4efte shim gaps the same as the 4efe ones as ive had my head re shimmed and pretty sure he shimmed it to the 4efe spec? need to know this asap as my cams seem to be getting damaged on the edges? rep given thanks Dean

ok people need your help again basically just rebuilt the engine to standard speck only modifications are decat full exhaust system ported mani nd wastegate hks fcd set at no cut on 12 sard fpr no filter fmic hks actuator car is set at 0.7 bar through actuator problem is car was...

ok i really need some help basically just rebuilt my engine standard spec etc after i cracked 3 pistons new parts fitted are head gasket head bolts new piston rings new oil oil and filter now built it all back up started priming the engine but theres no oil getting around wat so...

need this asap if any1 can please pm me his number thanks Dean

ok urgently needed standard 4efte pistos x 4 can any1 help would prefer brand new! does any1 have part numbers? any help please thanks Dean

ok im stripping my engine etc but cannot get the bottom pully bolt off is it a right hand thread or left? any tips? thanks Dean

ok i just need to borrow for like 10 seconds a 38mm external wastegate gasket just to draw around. around the west midlands/ birmingham/ staffordshire area :) Dean

ok just wondering wether the gt rear axel with the discs fits on to the starlet sportif? i know the glanza one does but my mate is breaking his gt so after the axel? any help cheers? thanks Dean

ok basically ive just fitted my sard rrfpr with a sard gauge i have ran the gauge straight off the side of the fpr so i came to set it up to 2.4 bar for when i get it set up tomorrow but the gauge goes up and down between 0 and 2 bar and if you adjust the reg to raise the pressure then the gauge...

basically my cars been set up on monday with my hks fcd and sard rrfpr, now i havent connected the fpr yet but after fitting the fcd i started the car but its running like a bag of shit its idling at 500rpm and really lumpy also the engine managment lights on and i can smell fuel bad! now the...

ok basically yesterday got back from jae parked the car up for an hour no probs then nipped back out i drove all of a mile then the car started fireing on 3/2 cylinders at first thought i thought id ran out of fuel so went and put some in but still the same the car litterally wont go over 30mph...

so last week i did the head gasket on the car i fitted new head gasket and thermostat which fixed my problem with the radiator expansion bottle throwing water out. but when i put it back together i accidently mixed the pipes up on the throttle body so steam was coming out of the exhaust it also...

ok i now have a major problem, over the last week i took all the head off because my water was pressurising through my radiator and out my overflow bottle indicating that the head gasket had gone between the cylinder and water lines. when i took the head off the head gasket had not gone? so i...

ok basically i need to know where the bottom pully markings should be set on? when my cams and distributer are all lined up? the 2 markings are (10 and 0)on the bottom pully. im sure its 0 but not 100% could someone please confirm. i really dont want piston clash! someone lent on the car...

could someone please tell me what bar i need to set the hks actuator at so it doesnt hit fuelcut? i was going to set it to .8 but was just thinking will it need to be set at .93 to not fuelcut? this is just tempary till iget my fpr and fcd set up but dont have these installed yet. thanks Dean

ok basically since i fitted the 4efte into my starlet sportif the tempature gauge hasnt worked. tomorrow im changing the thermostat but i need to know wether the tempature sender is faulty? how could i test the gauge to see if its a short or the senders nackered? also which one is the...

ok im pretty sure that the 4efe head gasket is the same as the 4efte but just need some1 to confirm please thanks Dean