What afr do you get in idle!
With emu and set up the injectors!
I set stock 295cc 0.9ms lagtime
and after 460cc 0,74ms lagtime
and on idle the afr is jumping between 13.8 and 14,4
That is to rich or did you get the same afr?
I really don't know what i should to!
is there anything more do to that 1,8-2bar boost will be safe?
Set up now:
Ross 74,5mm low comp. pistons
Pauter rods
cruise 1,2mm head gasket
speedvision valve springs
new toyota head bolts
460cc speedvision inj.
e-manage ultimate with pres. sens. and all harness
greddy head range...
I have a little Problem!
I don't know if this is possible!
I run the first time for this year my 4efte Corolla!
And i see over 130° Oil temp.!
But this shouldn't be possilbe because why should i get this oil temp when water is on 90°!
That is strange!
Maybe my Oil temp gauge...
Will this turbo be very laggy on a 4e?
More than a td04l?
When will it start spool?
My setup is
Ross 74,5 low comp. pistions
pauter rods
1,2mm metal head gasket
speedvision valve springs
fmic with 50mm and 60mm hard piping
mazda rx7 injectors 460cc
e-manage ultimate
Blitz...
I have a problem!
No i have speedvision 460cc injectors
Set at EMU
Stock 295cc 0,90ms lagtime
Now 460cc 0,74ms lagtime
But it runs very lean!
I had to lower the size from 460cc to 350cc than it runs a AFR between 13,9 and 14,8 but when idling the AFR should stay arround...
Hello!
Now my setup is ready and everything is running!
speedvision td04l kit
speedvision valvesprings
fully forged engine
330cc injectors
running on e-manage ultimate
1,4bar boost with biltz i-color spec r
no the injectors ar to small!
What injectors should i get?
I...
I have a problem with my e-manage ultimate!
Everything is working i can start the engine!
But the monitoring of the ignition is complet wrong!
-200 to -14
It is really strange!
Can anybody help?
Does anybody no the injector lag times of
Stock 295cc 4efte injectors
and
330cc Speedvision injectors
That would help a lot!
And what injector size should i get for 1,4-1,5bar on td04l!
I thougt 440cc-460cc
I am looking hard to find a english instruction for my SBC I-Color SpecR!
Please can anyone help!
I searched by google and everywhere but i didn't find something!
Look at this this could be interesting for somebody!
http://cgi.ebay.com/ebaymotors/Used-HKS-GTSS-Turbo-Kit-FMIC-HKS-Fcon-EP91-4EFTE_W0QQcmdZViewItemQQ_trksidZp1713Q2em153Q2el1262QQcategoryZ33742QQihZ019QQitemZ290265228081QQrdZ1
I am not the seller but if someone will uprade this would be...
Which one yhould i get?
This one
http://www.nengun.com/sard/fuel-regulator-8mm-nipple
or this one
http://www.nengun.com/sard/fuel-regulator-type-rj
i really don't no what is better when i take the type rj!
Please help me
I have a really strange boost problem!
The turbo starts spooling normal than boost goes up to 0.9bar and than falls off to 0.25bbar and goes up!
I had a leak in the intercooler piping and solved this problem today!
And the problem is allready here!
I don't have any idea what this...
Hello!
I want to know what boost will be safe on my engine!
My mods are
Speedvision Uprated Valve Springs
Speedvision 1,2mm headgasket
Ross 74,5mm racing pistons
pauter rods
td04l turbo with internal wastegate
Speedvision td04 mani
speedvision downpipe
all gaskets new
bearing...
So know i have my new setup nearly complet!
I have
Jam Racing ECU
Ross 74,5mm pistons
Pauter forged rods
all gaskets new
1,2mm metal heatgasket
uprated valve springs
ss mani
ss downpipe
td04l turbo with internal wastegate
330cc injectors
So i am waiting on my...