Search results

Hi guys and greetings from Cyprus!!! I come up with this problem within these few days and don't really know what to check or what is the cause ... My Ep91 Glanza V when i am trying to hit boost on every gear it starts to misfire.. This weird misfires come with a weird jump on the rev...

Hi guys and greetings from Cyprus!!! I am interested in finding the Compressor map of IHI VF30 turbo and get some explanations about it so i can see where the turbo is efficient and know at what boost is the limits. I currently boost it at 1.55 bar and overboost it to 1.8 bar for some Rpm's...

Hey guys and greetings from Cyprus!!! I have this problem with the 2nd gear and i dont know what may be cause it!!!:confused: When i am trying to powershift from 1st to 2nd gear i cant put it and i mis-shift!!! The first time i thought it was on me but then i tried again and again and...

Hey guys and greetings from Cyprus once again!!!! There is something bothering me for quite a while!! Its about 3 months that i put a Cusco front strut bar , a Cusco Roll cage and a 3 point rear strut bar and i notice that the car doesnt spin much and like it was before.. The car before i put...

Hello guys and greetings from Cyprus once again!!!! I have a friend with a forged 5E EP85 and will upgrade the turbo(previous was a tdo5 16g subaru turbo) and we are in a dilemma between a vf34 from a Spec-c and a Td05HR-16G from an Evo 9!!!! :confused: The car is a drag car and we launch...

hello guys and greetings from cyprus!!!! I just wonder what is the preferable camber setup for drag use????:confused: any info will be aprecciated!!!! ;) Thanks in advance!!

hello guys!!!! I wonder if a 5E inlet and cams would work beter than the 4E ones on a forged 4E VF30 setup????? :confused: The car is about to boost up to 1.6-1.7 bar!!!! With 5E inlet and cams i am about to see any difference in hp or torque or lag??? Some guys here said that it will...

Hello guys and greetings from Cyprus!!!! :) I wonder if an EP82 roll cage fits to an EP91!!! :/ I found a roll cage ( i think is CUSCO but not sure) but it was in an EP82... It will fit in my Glanza or it would need modifications as i dont want to cut my Glanza because its a street daily...

Hello guys!!! I just wondering if i could match an Apex PFC Ecu from a different car i.e from a Honda , Subaru , Evo to a EP91 Glanza by doing a harness that match to the EP91 main harness??:confused:

Hello and greetings from Cyprus again!!!!! What is your opinion about Athena 1.2mm hg and how are these gaskets handle the excesive boost i.e over 1.4 bar.... :confused: Did anyone have any problems with these gaskets and where are their limits on boost??? Thanks a lot in advance!!!!:)

Hello guys !!! Once again i need your help but this time its not for my car... I have a friend who has a forged 5e Glanza and we have the following problem... When the car is cold it starts perfectly but if the car get to the proper temperature it wont start until we leave the car to cool...

Hello guys!!!! After my cylinder block cracked, as i said in a previous thread, i decided to rebuild my engine due to the fact that all the forged parts of mine are in good condition... :) My question is , if i dont use wiseco piston rings and use other brand's rings such as Hastings would i...

hello guys !!! Just looking for a little info.... Does anyone know surely if there are any differences between a 4EFE n/a cylinder block and a 4EFTE turbo cylinder block??? Because i 've cracked a 4efte cylnder and just wondering if i can use a n/a engine's cylinder block....:confused:

Hello guys and greetings from Cyprus!!!!! I am thinking of using a TRD headgasket on my forged 4E vf30 setup due to Cruise hg failure.... I was running a 1.2mm hg and now i am thinking of using a TRD 0.6mm hg... Any opinions or expiriences about TRD gasket and what is the limitation of...

[ Hello guys i am upgrading to a VF30 turbo from a Impreza v7 and i wonder if i will see any difference in horsepower from my previous VF24.. I had to change the turbo cause the vf24 decided to die without warning...I made 253 atw with the 24 at 1.5bar ...how much to expect now and what are the...

hello guys!!! A friend of mine has a '95 GT Turbo and the only mods it has is a front mount, blitz spark leads, and a 2.5 inch straigh through exhaust system.... The car now is boosting at 0.7 and we found a nicely ported exhaust manifold but we dont know the gains of that What do you...

Hello guys!!! Got to the local dyno today to see the results of my new setup.... The car on a VF24 boosting about 1.5 bar on 40 degrees outside temperature and tuned on a S-AFC2 made the following numbers... 253.6 PS at the wheels @ 6802 rpms 289.9 PS at the fly @6802 rpms 34kgm of torque...

Hello to everyone!!! I own a '99 Glanza V and i want to know if is there a speed limiter on the factory ECU??? i know most japanese cars have but i didn't understand really if i hit the limiter in mine... If it has at what speed is it set and how i would i notice it....???? Thanks in advance:)

Hello to everybody!!!! I just wondering what is the limits of Exedy organic clutches???? Thanks in advance!!!!

Hello guys!!!! I was just wondering, how much nitrous can i spray on a forged 4E on a close to stock compression ratio???? Thanks in advance!!