Search results

Thanx again. Il do that

Yeh a small difference lol. So i shouldnt worry to much just get it remapped and all will be well? I did these tests yesterday and today its really running badly seems air to fuel ratios are all messed up acceleration is bad with popping. At idle its at 1000rpm seems fine and sparks were also...

Hi I recently fitted a Mitsh td05h 16g on my ep91 5efte setup. I had the stock ct9b turbo which was mapped using a unichip. The car had been sitting for about 3-4 months before all was fitted. When all was completer on the 1st test run I noticed a flat spot at 3.8k rpm all the way to 4.8ish...

Hey Guys, A mate is selling EVO 2 injectors the Yellow ones rated at 510 cc from what i gather. Is anyone else using them on the site plus what was required to get them to fit 100% and if possible can anyone tell me about the resistor packs they have in their cars . I saw the Helpful section...

Sup bro, you had said you got a td05h turbo running on stock internals. What mods did you use for this. I have a 5efte setup with stock 4efte turbo and uprated tmic and ported manifold.

yo bro , what turbo did you get i was also looking at that turbo from mr turbo.

ok pulled turbo apart and there a was no oil in the water chamber or vice versa. Seems my cylinder head is warped. darnit luckily got a spare engine.

Can anyone please post a pic of the gasket that is warn out when oil is fed into the intercooler. :(

thanx alot for the info Jay. so the parts that are salvageable ...can i use them on the ct9b turbo to sought out the oil leak. im not to clued up on turbos but i know seeing lots of oil in my intercooler says the turbo is leakn oil

hey guys, my ct9b from my ep91 started leakn oil terribly and found a smashed donor ep82. turbo looked fine just needed to be oiled a bit turbines were stiff.but when the mechanic started the car the dipstick was white after a few mins of idling n mild reving. any ideas if there is something...

Wow that sounds ...time consuming. It does not just fit in place are they not the same size. Oh yah it might not work to well as i have ABS and that is only on the Glanza's . Thanx for the info will pass till i find a ep91 manual ecu.

Hi , I searched abit and failed to find info . Please can some one tell me if it is possible to use a manual GT ECu in a Glanza V. If so what is the differnce or impact on this . I am currently using a Glanza Auto ecu.

Im not sure on the details of the turbo yet but as soon as i find out will let you know. I am going to see it later today I just wanted to know whom has used one and what soght of power was got out though 165whp is a bit lower than expect. What sought of injector size would be suited to run it...

Hey guys any one know much about this turbo and what it compares like against a td05/6 im aware that it is large for 4efte but for a 5e setup should be more responsive.

Hi i just fitted a new HG (4efte original) from a non original. There was no smoke before the HG change , Now i get a Smoke grenade puff of smoke 1st dark bluish followed by white . Same when i rev and when idle white smoke not alot but enough to leave smoke trails. Alot of hesitation and...

Thanx alot rep added , I originally had a pyan HG on and it had alot of extra holes and have been through 3. So i guess the saying cheap and nasty applies. :)

Hey , I read that the original head gasket is the best but is it recommended for a 5efte setup with ct9 turbo. The code i think is 11115-11071 is this one fine for my setup.

Thanx for the info finx.

thanx for the info guys , Ok it defo aint oild from top up but will look into cam cover and dipstick area

Hey guys , I got an oil leak i cant make out where from. My alternator is covered in oil and well mainly around that right side. I also hear a loose light metally noise when i accelerate coming from the alternator area. help