Search results

Hi can somebody tell if the OEM LSD diff from MR-2 fits in a Glanza gearbox? think its also an C-family gearbox. would such LSD stand Glanza with 180PS-190PS ?

Hi, i build a 4efe Turbo. now i have problem with to much boost at 1/4 mile starting. To much wheelspin. So i think about OEM boost solenoid. this my car doesnt have but i use EP82 turbo ECU. so i have the PIN from ECU to be able to use such solenoid. I think about using normal Solenoid with...

hi, i want to buy exedy stage 2 3 paddle clutch for my starlet 4efte. Found some kits what fitte to 4age? this got same partnumber like the starlet turbo kit? are these same? Im some shops is only starlet listet , other is only 4age listed. i think should be TK02T441 ? is this correct?

Hi, iam planig install an Greddy EMU. Have already Greddy Loom, A/F gauge with output chanal for EMU I want to erase Fuelcut to run higher Boost with needed injection and ignition adjusting. WILL I NEED SEPERAT GREDDY BOOST SENSOR? Is OEM MAP sensor always needed?

Hi, Iam from germany and search for clear cam cover but nothingto found. so i tryed to make one self. Used PMMA but got problems with the Tempratur. Always little Bubbles in the Plastic. So i searched an little company which can make these covers. I got an figure to make an copy in clear. They...

Hi, got my 4efte rebuild with Wössner pistons and Scat rods and ACL bearing. Can anyone tell what oil is original equipped in 4efte engines? what is proposed from Toyota? I heard after rebuild, an engine should run first 1000km with mineralic oil, whats with semi synthetic? should i use pure...

hi, i search the OEM Efi pipe WITH she sticker plate "16Valve EFI" (from air cleaner to turbo). shipping to germany needed. OEM BOV is not needed hope someone can help

hi, i search the plastic connector for an OEM 4efte knock sensor. my plug is broken. Will need the plastic hosing and the PIN with little wire. Hope someone can cut out from an old engine loom? or what also will help is an Partnumber. I used toyoDIY.com but i couldnt fint connectors thx,Jan

hi, got my 4efte rebuild (wössner pistons), block and head skimmed. so my pistons are 0.10mm higher than the block. I want to use 0.6mm TRD head gasket because want better response with OEM CT9. I would only have 0.5mm from the piston to the head if all is fitted. Can there be an contact...

CR 8,3:1 with Paseo HG MLS 0.5mm? heard there are paseos with an 0,5mm metal Headgasket ? this should be in the second generetion of 5efe? can anyone tell me an partnumber? can i fit 5efe HG at an 4efte engine? thx,for help

hi, i`am little confused ablout the main bearings in an 4efte. The original once have marks from 1 until 5. If i buy ACL bearings they have STD or oversize. I think oversize is only needed if the crank is regrounded. but what size habe STD ACL ones? at my 4efte first bearing is marked as 2 and...

Hi, i put an oem 4efe, with thicker headgasket an selfmade adjustable Camgear to turbo. Uses oem 4efte distibutor,turbo, ecu,injectors etc. but if i use scobe to flash the timing, i run on 20° btcp. if is change to 10° btcp i will burn my pistons and have much less power.dont understand. all...

hi, i am interested if the 2 pulleys got same mares on it. i know there are different kinds of pulley, damperd, some lighter OEM. but do they all got same timing marks?

I have to change my syncros. Problem is, the new once got other teath and when i packed the rings out, doesnt realized the difference. So i dont realy know, if the syncros now are correct. here are 2 pics http://s7.directupload.net/file/d/2478/upx5eoix_jpg.htm...

i have to put in my engine new bearings. Had no problems, but building new engine. I watched at the OEM bearing in my engine, there are small number printed.I think this is the size of the bearing. cylinder 1 got number 1 , 2 cylinder 2 got 2 , 2 cylinder 3 got 1, 2 cylinder 4 got 2, 2 so...

hi, i heard form someone who build an 7afte, he wants to upgrade the piston cooling by adding Oil bleeders in block which spray oil at the piston from below. Dont know how its real called in english. Does some put this in an 4efte? do i need this for an normal upgrade in a streetcar? I dont...

hi, i am forging my 4efte. I orderd today the 74,5mm wössner pistons. Scat rods i already have recieved. The pistons make an CR of 8,0. What headgasket should i use? thought about 1,2mm? if i can raise the CR a little an run also safe? this year i only want use oem CT9, but later hybrid.

For sale: Final drive set from Auris ZRE151, 1.6 with C50 or C53 gearbox,it has 4,529, trd once have 4,7 so its nearly same . VIN was SB1KV56E60F005683. you can check at www.toyodiy.com. Will fit the starlet Turbo gearboxes. I got this for my car, but decited only use original Final gear...

hi, I need forged rods in germany. So i have to import. The traders here in forum sell scat rods for around 365 gbp. At ebay.com Scat rods are available for 200 gbp + shipping. Are these parts same quality and total same?! why are these rods in USA so cheap?? If i Import from USA, 200gbp and...

Hi, Iam planing forge my engine. Need forged rods for this. Would prefer new once which you wont need anymore. Groupbuy would be also good, to get the price cheaper. Dont want unknown ebay stuff