Search results

EDITED BY ADMIN. Please read the classified rules and post in the correct format in the correct section.

Hi guys and gals. Got a problem with idle, engine management light keeps coming up when you get to 60mph or around 3K rpm. logged code for air temp sensor which has been replaced still fault there. any ideas i think broken wire or circuit problem? any contribution welcome and im fairly sure...

hello Guys and Gals desperately after rear calipers must be in good working order PLEASE HELP Paul

hi guys and gals, just a quick question really, at some point i want to go for engine management and i wanted to know the costs of this?, how successful its been powerwise ? and whats a good type to go for emanage or unichip all help gladly recieved Paul

hello everyone just been having a look online at insurance for the hell of it, got bell to quote £790 fully comp with no volantary excess declared modded with 4yrs no claims with the usual bit and bobs. Not too bad i think your agree so i thought i would see how much to get fiancee put on...

hi guys and gals as you all know its getting much colder out now and im freezing my royal naynays off.Due to the heat through the heater is as hot as it should be only luke warm through centre vents and slightly warmer to screen and floor (i know its partually due to centre vents being fresh...

hi everyone, not been on in a while well basically i want to know what everyone is running boost wise on starlet. i got decat, exhaust, hybrid turbo, air filter relocation, forged engine, fuel pump, rrfpr, fmic, fcd, boost controller, plugs and leads, oe mani ground out (a lot) etc and had...

hello.... i currently only have 2 6x9 bridged on amp, nothing else at the moment as front ones blew. is there anywhere else you guys and gals have put them i was think in rear side panels ? ? thank you :) Paul

Hi everyone, where to start When i had just started modding i got the compression up to 155-160psi over time this dropped to 130 across due to 4cracked pistons (ARRRHHH) Now i have gone for wiseco pistons and had 3thou off the head. I want to get compression back up to standard (dont want to...

Hi everyone been a while since i was last on as car me garage with engine out Just a quick question really want to go forged now.... obviously and really want to know has anyone fitted wiseco pistons on the stock rods and if you had any trouble with doing so. I dont have loads of money so...

Need to get a turbo rebuilt, as i got two ct9's now i was thinking about sorting out the seals and bearings in one myself but not sure whether its worth the £70 if i get it wrong. I dont have much money anymore as mister burwash has it ! lol does anyone know of anyone that does private jobs...

Hi everyone recently bought a turbo off someone on here, who asurred me that there were no cracks, shaft play, or oil leaks Have now fitted it 2weeks later To find actually its pissing oil and has shaft play now its been run. Can i report people on this site to anyone ? Only i am pissed...

Hi guys, Im carrying out timing belt change and need to know best way to get crank pulley off, i know there is a special tool from toyota for this but obviously cant get hold of it. I did have proper instructions from toyota on replacment of belt, but have subsquently lost them. Does anyone...

hi guys and gals, i want to get a boost controller, but am very inexperienced in what ones are easy to work, reliable, cost etc what one do you recommend i go for ? cheers Paul

hi, got loads of judder from clutch when cold ..... yeah i know you would expect it to be worse when hot. really what i want to know its regarding getting a flywheel skim is it possible on these or just better to get new fly. I havent taken it off yet so i dont know how 'high spotted' it is...

Im in need of a ct9a/b (dont mind) must be crack free......... i know im asking a lot Please Pm me if you have anything in need desperately i cant keep driving my fiancee fiesta ! arrrrhhhhh push rods

hi guys how many people have carried out a ct9 rebuild on ere successfully ? i know its not too much for seals but with the risk of making a hash of it, is it worth the risk ? Paul

hi guys got the autobahn mani looks good, shame that autobahn plate upside down but still (Cheers Dave B) Well if anyone who has also got this, can you tell me how you fit the studs as obviously they dont have anything to tighten too or maybe im being stupid Cheers Paul AS NO1 WILL...

all new parts wanted clutch...... autobahn fmic...... uprated fuel pump...... 8.5mm h.t leads (clip type) iridium plugs (heat 7) oh and probably a forged engine ..... but if anyone has had it recently done or offering a good price on having it done p.m me please Paul

driving on motorway this morn and noticed boost dropped .... (normally runnig 0.9bar) noticed when foot flat to floor at 80mph it would only boost to 0.7bar really all i want to know is there such thing as negative boost creep ?!