Search results

i cant work out how to sell my car on this forum. wat do i have to do?

does any one no how u fit a hks blow of valve to a autobahn intercooler?? i need a reducer i think 32mm to 18 or 19mm can anyone link me?? harry

i need a manifold and manifold to turbo gasket where do i get them from link me up or pm me boys

hello can anyone send me a link of if uv gt either of the parts pm me, i want a mild steel manifold for a ct9 and a air filter relocation kit, and a dump valve, if anyones gt the parts please contact me, harry

i want a good ct9 hybrid if anyone got one and i realli want a good manifold cause atm iv just gt a ported one, i dont want sum shit heap i want a sick one so pm what u got

i want to go lower on my starlet but i dont want coilovers just springs, what shud i go 4 sum 1 send me a link please. harry

i have a ep91 1996 glanza and im putting a new exedy stage 1 clutch in 2morrow and i need to know how much and what gearbox oil i need? harry

is 1.1 bar on a ct9 turbo on a glanza ok, bearing in mind i am running me boost gauge of my bov, i no this is slighlty inaccurate do you no if wen its run of the bov if this inacurracy is saying that its higher boost than it actually is or is it saying it lower boost than it actually is? harry

alrite my car sometimes seems a bit reluctant to start every since i fitted a rrfpr and put colder plugs in it, could either of them be the problem? will this probably change after i get it set up on the rolling road,? harry

i want a clutch that i can use for everyday use, im guna be running just under 200 bhp and i need a clutch that can hak it so if any ones got one please pm me, harry

what clutch would u recommend for a 190bhp glanza? can people post links? harry

my clutch is slipping do i need an uprated clutch if im running only 180bhp? will this clutch be ok? http://cgi.ebay.co.uk/ws/eBayISAPI.dll?ViewItem&item=180466857203&ssPageName=STRK:MEWAX:IT#ht_1673wt_941

i have put my new hks actuator on and set it to 121mm length wich is supposable sets the turbo to run at 1bar, i hae connected my boost gauge to the bov pipe but wen i boost it says it running at 1.3bar? is this actually over boosting or is it because running the gauge of the bov isnt that...

alrite boys now i dont really giv a shit about how much fuel i use as longs as its being burned by a good engine, but i will soon be uping my boost to 1bar from standard and i need to tell my boss about fuel effiecency so i can claim for my petrol for work, will i be looking at much worse...

any on got links of manual boost controllers that wud be good for starlets? or anyone got any for sale. harry

if anyones got a boost controller please contact me pm harry

im driving a 98 glanza with a fmic actuator rrfpr decat ported manifold, what plugs wud u suggest iv gt sum ngk but i duno if there the rite ones, whats everyone else using? harry

hello i want to relocate me air filter iv just removed me air con so im good 2 go but im sceptical about wat would happen if it rains badly surly it wud be bad to force water in? has anyone had any problems with this and also on the existing induction pipe there is a tube that goes to the hi/lo...

does anyone hav a rrfpr for a glanza or does anyone recommend me one? i dont want nothing special just something that will do the job, harry

i have a glanza and it has a fmic and a ported standard manifold with a decat and a fuel cut defender, and a uprated actuator is a rrfpr neccesary? harry