Search results

Hi I recently fitted a Mitsh td05h 16g on my ep91 5efte setup. I had the stock ct9b turbo which was mapped using a unichip. The car had been sitting for about 3-4 months before all was fitted. When all was completer on the 1st test run I noticed a flat spot at 3.8k rpm all the way to 4.8ish...

Hey Guys, A mate is selling EVO 2 injectors the Yellow ones rated at 510 cc from what i gather. Is anyone else using them on the site plus what was required to get them to fit 100% and if possible can anyone tell me about the resistor packs they have in their cars . I saw the Helpful section...

hey guys, my ct9b from my ep91 started leakn oil terribly and found a smashed donor ep82. turbo looked fine just needed to be oiled a bit turbines were stiff.but when the mechanic started the car the dipstick was white after a few mins of idling n mild reving. any ideas if there is something...

Hi , I searched abit and failed to find info . Please can some one tell me if it is possible to use a manual GT ECu in a Glanza V. If so what is the differnce or impact on this . I am currently using a Glanza Auto ecu.

Hey guys any one know much about this turbo and what it compares like against a td05/6 im aware that it is large for 4efte but for a 5e setup should be more responsive.

Hi i just fitted a new HG (4efte original) from a non original. There was no smoke before the HG change , Now i get a Smoke grenade puff of smoke 1st dark bluish followed by white . Same when i rev and when idle white smoke not alot but enough to leave smoke trails. Alot of hesitation and...

Hey , I read that the original head gasket is the best but is it recommended for a 5efte setup with ct9 turbo. The code i think is 11115-11071 is this one fine for my setup.

Hey guys , I got an oil leak i cant make out where from. My alternator is covered in oil and well mainly around that right side. I also hear a loose light metally noise when i accelerate coming from the alternator area. help

Hey guys, i had an oil leak some time ago and my abs goes off when i turn left is there anything else that needs to be cleaned besides the sensor. thanx

Hey, My mechanic fitted in new rings , bearings and shaved piston heads from 5efe engine as two 4efte ones cracked. when engine is turned on i have all three boost lights on and engine light. Anything we have missed. :confused:

As stated above I'd like to know how many hp/kw your rides are pushing. This is more of a bench mark for me so i know when i get mine mapped what sought of power i should be expecting. A simple :hp xx mods:xx would do i guess Just cracked two pistons from 4efte so shaved my 5e pistons :( till...

http://www.jon44w.com/site3/viewthread.php?tid=923 Im salivating ....is this completly fabricated or is it from another model starlet. I need to know so i can get my Hands on one and mod it. Thanx :drive:

Hey, My oil is leaking from my tapid cover . I initially had a wornout HG and got it changed. I now have to much compression or so it seems but im not too clued up so wouldnt know'. I am using a Pyan gasket not completely steel but a softer metal. It was initally leaking oil from my...

A mate of mine said he has a turbo from a Mitsubishi pajero 4D56T. can this be fitted on my glanza . Well after geting a mani built for it. More importantly would it be worth it. I have a 5e setup with stock mani and ct9.

Im not too clued about gearboxes but can a 4e clutch kit fit a 3e flywheel. i Have a 3e gearbox bell housing on a RunX gearbox not sure of the code and the 3e flywheel is drilled to fit 5e block. I read the 3e/2e flywheel is a ton heavier than the 4e but can the clutch kit fit each other. I...

Hey guys , What gear box does the runx 1.4 use?? I am using one and it has really short gears. Well In 5th at 100km/h i am at 3.5k rpm is that Right. Well i wont complain that it is not delivering it does but i feel like i need a 6th gear after the conversion from auto - manu

Hey guys, i just got my cylinder head re-torqued over the week end after fitting in the 5e setup. Now my engine is overheating. I cant see any leaks except for a few oil drops which is another thing woring me. I did not use a timing gun to re set up the timing . Would this be a cause to the...

I recently just did the conversion. I am having problems with hesititation from 1-3 k RPm on gear 1-3 from what i have noticed. Which i read is the lambda sensor so i got one that i will fit. Will this sought out my boosting issue. I have not fitted in the boost guage as well just havnt had...

Hey guys , This has been covered before but failed to find a proper illustration on the cales that connected to the old auto stick. Can some one please upload some pics on what cables need to be rewired for the manual conversion to start up. Or links with illustrations. Thanx

Whom has done this and did it work out. Im keeping my options open as the only other gearbox i have direct access to is from a smashed ep95 . Did i say really badly smashed like the car swerved a bus then smacked a cow before landing in a ditch. So there is a better condition 2e from a tazz cant...