Search results

Hello mates! I'm planning to buy this part at ebay. 90-95 Toyota Starlet EP82 GREDDY Emanage Blue Plug and Play Harness But the seller is saying something about "The Ignition Control for the Emanage does not function natively for distributor base engines without a converter". Anyone have an...

Hello! mates, I have a question regarding the behavior of your engine when you short the TE1 and E1 as I have confusing result. 1) 4EFTE gen 1, when shorted the TE1 and E1 the engine becomes relax, the rpm goes down a little. 2) 4EFTE gen2, when shorted the TE1 and E1 the engine becomes...

Hello! mates, I'm experiencing hesitation at high rpm everytime I suddenly (aggressive) stepped on the gas pedal and the rpm reaches 4k. I noticed that my distributor is for 5EFHE, do you think that this is the one causing the hesitation? does 5efhe dizzy is not compatible o match with 4efte...

Hi! I just installed an emanage blue with main harness/injector harness and ignition control harness. I'm having problem starting the engine, most of the time hard starting, if the ignition control connector is plugged in. But if I unplugged the ignition control harness and put a jumper wire on...

Hello mates, Just a quick question, what is the speed cut of a stock ecu of 4efte? I experienced power loss after reaching 200 kph but some says it should be only @ 180 kph. Thanks

Hello! Does anyone have the wiring diagram on how to wire the actuator/idle-up for head light? I have a problem which drops the RPM whenever I turned ON my head light or braking. Thanks

Hello mates! I have an APEXi AVCR and I wired it correctly based on the supplied wiring diagram for 4EFTE 2nd gen engines. The AVCR detects my throttle voltage as 4.5v when closed, so I set the AVCR arrow down but when I'm revving the AVCR is not detecting how many percent open is my...

Hi! anyone have a picture on how to install the avcr solenoid on a CT9 turbo with stock actuator. TIA

Hello! Can you help me on how to test the coolant sensor? The one with "GREEN" connector. I noticed that when my engine is cold my idle is around 1.3k rpm and it takes a while (10-20 mins) to drop to 850 rpm. Thanks

Hello, I have an APEXi SAFC II (AFC3 100-03874). Before it was working pretty well and suddenly the problem occur. The problem is, it would not retain the saved setting/program on its File 2 preset. Programming File 1 is OK, but when you programmed File 2, the setting won't save and...

Hello mates! I just want to confirm if the stock flywheel weight of 4EFTE is 6.2Kg? If does so, is it safe to replace it with a 4kg flywheel considering it will be a daily driven car. Thanks

Good Day! Mates, Does 4EFTE is a Non-Interference Head? Meaning when the timing belt got busted/ripped you just replace it and no damage to the valves. I know 4AGE's (20V) are designed for that. What about the 4EFTE's? Thanks and regards

Dear mates, Based on the guide I read in this site, the check engine will flash if you bridge the TE1 and E1. Does it change also the sound of the engine? Is there a rev change? I tried to bridge my TE1 and E1 but nothing happen, no change in engine rev. I don't have a check engine light...

Dear mates, I just saw one thread showing how to fix our TPS but according to my friend the guide is good only if you have a stock engine (no modification yet). Is there another guide to fix/correct the TPS on modified engines (e.g. installed after market parts)? Thanks and regards

Hello Mates, I'm looking for the following parts but you should be living in dublin or near it, since I'm here in the Philippines and I will only ask my brother's help on the negotiation since he is living in Dublin. Looking for: (All parts are for 4EFTE 1st Generation) Greddy or HKS...

Hello! mates, Does any one of you have a guide on how to replace the Positive Crankcase Ventilation (PCV)? Thanks

Hello! Mates, What is the correct idling for 4EFTE (Hot & Cold Engine). Mine is 1.2K RPM Cold and 1.1K RPM Hot. Thanks

Hello! mates, I have this problem (fluttering sound after blow-off) after the mechanic adjust the throtlle. The problem started when I asked our mechanic to adjust the idling rpm, for me it's high (1.2k RPM cold, 1.1k RPM hot). The mechanic adjusted the TPS, idle stop screw, and the screw...

Hello! I bougth a car with 4EFTE installed and the previous owner gave me this BLITZ Twin SBC. Can you help me on how to install this? Thanks