Search results

Hey guys, I'm running a BPU GT. Mods: -FMIC -315cc injectors -SARD FPR @ 50psi base -Intake -2.5" Turbo back straight pipe -Zisco Manifold -HKS Actuator -Blitz Access ECU My boost creeps up to 14psi, then settles at 12. At the point it's at 14, my AFR is at about 13.8:1, then once...

Dave, what is the fastest you could get me a front wheel bearing kit? I called and emailed you, and I know it's a Sunday, just making sure I've got all the bases covered as it's urgent. Thanks Dave.

Hey guys. I've been experiencing a noise coming from the chassis of my EP82, it's constant from 40km/h up, getting progressively worse. It BARELY and I mean very very slightly vibrates the steering wheel, and it's more of a sound/howl that I can feel all around me, more than in the steering...

As title states, if you have one, or know where I could get one, please let me know. Thank you.

Odd issue here fella's. I went to adjust my intercooler piping, and noticed the pipe secured directly to the turbo, as I pulled it, was twisting the actual compressor housing on the turbo, independently from the center section! The car has been using some oil as of late, especially on boost...

Does anyone have a pic of these installed on their EP? I think I may have one installed backwards as my tires are wearing unevenly. Any help would be great!

I just fitted my HKS actuator, and have it set at 1 bar. The car will spike to 15 psi, but falls off to only 12 near redline. Is there anything I can do about this, look into etc?? I'd think nearly any engine should be able to supply the tiny CT9 with enough flow to keep it boosting? I've hot...

Hello, As stated in my MBC thread, I can't seem to achieve more than about 13 psi boost in my GT, with a properly installed MBC. Cranked way up or all the way down makes no difference, even when disconnecting the wastegate entirely, no noticeable change in boost. I'm positive I don't have any...

Hey all, I've decided to put up this write up, as I went through this dillema, I know there are a few of you out there that may be up against this as well. With this setup, I deleted over 2 feet of charge piping, while retaining a clean look, and avoiding that bologna "over the manifold" pipe...

Hey, I'm running 13 psi of boost, and approx. 13.2:1 AFR @ 6000RPM, which then dips to about a 12.5:1 past that. This is a little too lean for my liking. I've got a blitz access ECU installed, and SARD FPR set at over 50psi base pressure. Amongst my other upgrades, these are the only ones that...

Hey, I'm looking for a washer fluid pump for my '92 GT. If you've got one to spare, please let me know. Thanks! Clyson

I see lots of instructions on here, but I have one question still. What do I do with the 2nd nipple on the actuator? Leave it open, plug it? I've got the MBC T'd between the compressor and the first nipple, but the nipple that (went) to the factory boost solenoid is open, is this correct?

Hey guys, just installed a Blitz SS BOV, using the same vacuum source as the stock BOV, and it rarely vents. I'm always compressor surging unless I'm WOT and shift at near 6k, I'll get a tiny "PFFT" and thats it...I've adjusted the set screw to maximum loose and tight either way, not much of a...

Hey guys, I popped the motor in the starlet, and am going to be posting it for sale in Canada here as soon as it's swapped and running. I'm going to be purchasing an ST205 Celica in it's stead, and was wondering if anyone knows a good forum in regards to these cars. Thanks a bundle, it was...

Hey guys, this is the #1 and only issue with my car, and I'd LOVE to get it sorted. About 65% of the time while driving, under moderate to hard acceleration, the steering wheel vibrates. Not violently, but probably half an inch back and forth, rapidly. This only happens at peak torque (around...

Hey fella's, just wondering if a clutch kit for a paseo will fit an EP82? Not much out there for the Exedy stage 2's for the "EP82" specific application, but lots for the paseo, do they share the same splines, diameter etc?? Any information would be great. Thanks, Clyson

Hey guys, simple enough, my slave is leaking fluid down the dranny, and I can't engage gears when it's cold out. Anywhere I can get a slave repair kit? Or a part # to order one here in canada? Are they possibly the same unit as a paseo? To bleed the slave, does it have it's own reservoir...

Hey guy's any of you thrown one of these kit's on your EP82? I know it requires a slight wiggle of the PS line and some bracketry, but is that really it? I like this kit more than the autobahn one due to the fact the autobahn won't fit with my Zisco manifold, and the HDI pipe goes in the...

I know Toytuning did, but they are down for a while. Does anyone know where I can source on of the 4 point front underbody braces, as well as RS*R panhard bars? Any help to point me in the right direction would be appreciated! Thanks, Clyson

Does that look like the right unit for my 1992 GT? Thanks a million fellas!