Search results

Hello guys, just wondering if this might work: cylinder 1&4 GT rods cylinder 2&3 Glanza V rods The diference in those 2 sets of rods is that GT rods are much thicker than the Glanza rods. would this mean serious bottom end imbalence? I am guessing it would still work without...

is it possible to convert to wideband permanently? the ecu read values 0-1v from our stock o2 sensors. but from what i have learnt wideband outputs 0-5 v. I wish for full time wideband...dnt know if this is feasible...i talked to some1 over here in mauritius but he told me its not possible. I...

I recently notice that my car misfires like crazy sometimes under full throttle.. then i would lift my foot up and then press again and then sometimes it would be ok and others not. I suspect it can be the plugs but not sure. I recently changed the distributor and all the leads seems good...

Hello, anyone has any experince with COP with EMU? Is it feasible? What other parts will I need besides EMU? Which coil would be ideal for 4efte? And any other parts that I might need? Wiring diagram plz. Thnaks

hello, can anyone tell me if I can fit RX 8 seats in glanza and still get the electric and heating options work? i understand i will have to modify the seat rails and cut the plugs and supply it with a power source but I am not sure if the seats needs an ecu to function. I do believe that...

Hello, I got my engine forged a few weeks back and since then I notice that the engine starts misfiring as soon as it goes past 1.0bar. I used to run 0.99 to 1.0bar on my previous setup and it used to run fine. I use a precision wastegate with a 1 bar spring in it. The wastegate is...

hello, I`ve just forged my engine and now i notice that the mechanic did not connect certain things back on the engine and I have no clue what these could be and what are their importance. I am providing pics for the missing connection plz let me know what goes there. Pic 1 - there are 2...

hello, are these a straight fit? With the marks spot on? any1 using them or had issues with them? thanks

Hi everyone, i have just damaged my engine while trying to configure my boost controller. :(:(:( Now I wish to change the engine instaed of repairing this one but as i got a few parts already in hand I am considering forging to 5e while am at it....just thinking whether it would be wise to...

Hello every1, can anyone help me connecting a precision 39 mm wastegate to a Greddy profec B boost controller? The wastegate does come with installation wiring instruction but not for electronic boost controllers. I previsously had an HKS wg and worked fine with the settings I chose on...

Hello, I have recently fited an uprated CAP clutch cover and after a few days i`ve noticed that when i switch to 2nd gear, it kind of crunch a bit to get into 2nd. I feel that at the gear knob...it will vibrate a bit but will go in...This happens only on 2nd gear. And constantly I hear a...

Its been second time that my mani leaking...actually its the welding that goes off by bits....any idea how i can solve this permanently? thanks

hello every1, I have noticed these few days a strage sound when I hit 1 bar. i am asuming that this is happening when the wastegate opens. Because when the waste gate open it used to make a different sound (screamer) but now when I go full throttle the car runs smoothly until the 1 bar is...

I have recently noticed that there are some thick greasy deposits in the water reserve tank for the radiator. When I open the radiator I can feel its a bit greasy near the cap but the water in it is clear. I am using a racing rad (double core) with a nissan N17 fan. The car is running...

hello, i`ve just installed a gt28r on a 4e, was working fine for lets say 5hours!!! now i can hear a stange noise coming from it as if the bearing is all f!!!!ckd. the vacumm line of my BOV was not connected and also the turbo had no air filter on it (i know that was stupid!!!!)...

Guys, are the tial wastegates atpturbo selling any good? Or any1 has got 1 for sale here? I will even consider turbosmart as well if any1 is selling. I am aiming 1.2 bar of boost. what spring rates will i require? thanks

hello all, I am just throwing up this thread to discuss a bit about the reliability of the traders on TGTT. I`ve recently bought pistons and HG from a trader over here but when i track I see its in the wrong country. Instead of mauritius the packet is in mauritania. I am not going to mention...

any1 knows where I can get a custom 1.2mm head gasket for a rebuild. No stock at speedvision and cruise is way too expensive.

hello all, a friend of mine gave me a turbo today. It seems be a good turbo.no shaft play. He also gave me a glanza mani for it. However i have never seen this type of turbo before. On it, is written : TOYOTA E Nothing else is written. And the oil feed is on top which means it must be...

Hello mates, according to you when going forged 4e to use godzilla turbo kit, which piston type is most suitable? flat or dished? or what compression ratio would achieve best results? How about the size of the Head gasket? The turbo seems quite big...since i dont want to lag much on...